Jump to content
SAU Community

Recommended Posts

finally sold the shell, engine & gearbox so here are the only parts i have left from my car, nothing other than whats on the list below

- Alternator: $100

- AC Unit: $70

- AC/ heater blower motor: $80

- passenger kick panel: $30

- under dash trim panel: $30

- AC fan: $60

- 1 stock coilpack: $30

- driver seat: $100

- dash cluster surround: $30

- throttle body sensor [tps]: $50

- wiper/washer bottle: $40

- brand new front rotors(gone orange from sitting outside): $110

- front pipe: $60

- turbo(missing actuator) & dump pipe: $160

- injector resistor: $40

- steering column surround: $40

- dimister switch: $20

- hazards/tune switch: $20

- power steering pump: $80

- power steering resevoir: $30

- battery: $60

- oil dipstick: $15

- drive/fan etc. belts all 3(brand new): $50

- windscreen wipers all 3: $30

- pipe that goes from turbo to afm: $30

- bov return pipe: $50

- turbo heat sheild: $40

- centre console: $30

- orange passenger indicator(slight crack and scratch, still works): $40

- little airvent that goes from airbox to front of bonnet: $30

located in mulgrave 3170, victoria.

will post at buyers expense

negotiable on prices for some of the things

cheers.

Link to comment
https://www.sau.com.au/forums/topic/326523-skyline-r32-parts-vic/
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

back from overseas and still got these parts for sale.. throw me an offer need the cash after this holiday! lol

- Alternator: $100

- AC Unit: $70

- AC/ heater blower motor: $80

- passenger kick panel: $30

- under dash trim panel: $30

- AC fan: $60

- 1 stock coilpack: $30

- driver seat: $100

- dash cluster surround: $30

- throttle body sensor [tps]: $50

- wiper/washer bottle: $40

- brand new front rotors(gone orange from sitting outside): $110

- front pipe: $60

- turbo(missing actuator) & dump pipe: $160

- injector resistor: $40

- steering column surround: $40

- dimister switch: $20

- hazards/tune switch: $20

- power steering pump: $80

- power steering resevoir: $30

- battery: $60

- oil dipstick: $15

- drive/fan etc. belts all 3(brand new): $50

- windscreen wipers all 3: $30

- pipe that goes from turbo to afm: $30

- bov return pipe: $50

- turbo heat sheild: $40

- centre console: $30

- orange passenger indicator(slight crack and scratch, still works): $40

- little airvent that goes from airbox to front of bonnet: $30

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...