Jump to content
SAU Community

My Smashed 260rs

e-clip

By e-clip,
in Four Door Family & Wagoneers

 Share

Recommended Posts

e-clip Enthusiast

e-clip

Posted
Posted (edited)

Well I was driving to work this morning as usual on the M1 in QLD and as I just got on the Highway and started to accelarate to 110KM/H I hear this bang at the front of the car and bits of stuff flying everywhere.

I was swearing my head off as you can unstand. I looked in front of me and I couldn't see anything unusual the cars infront didn't stop or seem to have problems.

I couldn't really stop on the M1 being so busy so I got to work and this what I found.

This is the piece of metal stuck in the front of my grill.

:P

post-47234-1278406935_thumb.jpg

post-47234-1278406956_thumb.jpg

post-47234-1278406981_thumb.jpg

post-47234-1278406999_thumb.jpg

Edited by e-clip
Link to comment
https://www.sau.com.au/forums/topic/327808-my-smashed-260rs/
Share on other sites
msports180 Mentor

msports180

Posted
Posted

Ouch...

Back in the old days ( i mean when i was a P plater) i had a awesome chrome tip on my stanza, heard this noise from behind looked in the rear view mirror and saw it bouncing down the road, bounce up and hit the car behind me in the windscreen... Yeah kinda felt bad.

jrm Veteran

jrm

Posted
Posted

Few years back driving the highway at 100kph or 110kph (can't remember the limit anymore) from Brisbane to the Gold Coast, cruising on my long drive back to Melbourne. Up in front of me in the same lane was a carrying furniture on the back - suddenly the tallboy flies off the back and hits the road in front of me, barely had time to swerve and nothing in the right lane - still managed to clip my passenger-side guard & blinker.

Crazy thing is - the guy didn't even notice... I tried flashing and honking, but he didn't get it clearly, so I followed him until his turn-off (maybe 15 minutes) and through the town, into a carpark and just fumed at him as I checked out the damage to the front of my car. He looked a bit stunned, and didn't really know why I was fuming at him until I pointed to where half his load had been (more stuff had subsequently fallen off). I laid into him for not tying it down, etc. I'm glad I followed him, if I'd pulled over before that I would never have caught up to him and I had nothing to write his number plate down on (I have a terrible memory).

He eventually stammers an apology and I managed to get it repaired through his insurance. I had been sitting fairly far back, and I hate to imagine what would have happened if I'd been following closer or hadn't been paying attention to swerve so quick (or if something had been in the right lane).

You were bloody unlucky with what you happened to your car, but - as others have said, at least it didn't fly up and hit the windscreen or do more damage.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...