Jump to content
SAU Community

Recommended Posts

hey all, im new to this site & skylines

i recently bought a R33 GTS4 paid about 3500 for it.

i was just wondering is there a way to disable the attesa system?

and then simply just plug it in again?

or is this only the R32's?

any feedback would be greatly appreciated:)

thanks

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/
Share on other sites

you cannot just pull out a fuse like in the 32's. this is because their system was electrical and the 33's are hydrological.

You can drain the resovior in the boot but the safest thing to do is take out the front drive shaft.

BTW, how did you manage a 33 gts4 for 3.5k? is it damaged?

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5356095
Share on other sites

The caniser in the boot runs down to the actuator on the O\S\R of the car, it pumps fluids to the transfer case and when the slip light is activated it then runs too the rear diff and is pumped around there aswell, then back too the canister. It does this because it is a high pressured pump that activates clutch packs in the transfer case, this is how the attesa system works. Do not take the fluid out of the clutch packs with be distroid and you will have to spend a lot of money and all the parts with be EX jap.

The fluid is a ATF fluid, at nissan we sell nissan Matic D which is what they used stock.

You can take the front propeller shaft out but thats it.

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5357381
Share on other sites

how would i pull out the shafts? just pull them out

your only taking out the front shaft.

It is located under the car more towards the drivers side next to the gear box area.

there are four bolts that attach it to the car, they are in pricks of a position to get off...

the thing i do is, move one bolt at a time to the best position possible for you to reach by rolling the car, undo it and take it off, roll your car a little back or forward so the next bolt is in the same position and repeat.

when you get good at it, you can have it off in 10-15 mins if that....

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5357421
Share on other sites

As said before.

You can only disconnect the 4wd system in the R32's electronically.

In the 33 and 34 you must remove the front drive shaft.

This is the shaft from your transferbox (the thing hanging off the drivers side of the gearbox) going up to the front diff.

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5359314
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...