Jump to content
SAU Community

2003 Nissan Skyline 350gt Manual, Nismo 19's. Sa

TBee
 Share

Recommended Posts

TBee Community Regular

TBee

Posted
Posted

PRICE DROPPED

Due to a change in circumstances I now offer up my 350GT for sale.

During my ownership this car has been a pleasure to own and has had no issues whatsoever.

The car is in excellent condition mechanically and cosmetically, is always garaged and not driven as much as I'd like to.

The car has some additional extras including >

- 19 x 8.5 (f) & 19 x 9.5 ® Nismo LM GT4 rims in near perfect condition with high end Sumitomo tyres (I have tyre receipts for $1300 around 6 months ago & receipts for alignment etc for same time) , heaps of tread left on super quality tyres.

- Adjustable height & dampening coilover suspension. I have it setup fairly high for convenience but can be dumped as low as you are keen!

- Recaro front seats - These almost look like factory fitment and match in perfectly with the standard interior. In excellent condition with no rips or stains.

- Aftermarket Double Din CD/DVD/TV/GPS/MP3 unit (GPS for Japan so no go here). - All works perfect.

- Aftermarket alarm / immobiliser integrated with the factory setup.

Factory Features

- MANUAL

- Brembo brakes - plenty of meat on pad and disc, has aftermarket pads which have kept the wheels pretty clean and tidy!

- Auto Climate control - works perfectly.

- Factory HID (or so Ive been told).

- 4 legitimate seats which makes this far more practical than a 350z !

- Factory Skyline mats front and rear means the carpets and inside still look fresh.

The car has all books and service history from Japan & Australia since ive owned it and has recently been serviced at Nissan and had oil and filter plus drive belts replaced. Running as sweet as it ever has and prime for a new owner!

This car also comes with 2 sets of keys plus the Valet key which is excellent for piece of mind and saves on the cash and hassles of getting freshies cut.

Price : $26,000

Location: Adelaide, SA

Contact : PM or txt me

Name : Tom

Ph number : 0402 350 435

I'm negotiable on price but keep it real.

See below for a few pics, ive got more and am happy to take any extras if needed.

gallery_16287_1473_90339.jpg

gallery_16287_1473_64421.jpg

gallery_16287_1473_44066.jpg

gallery_16287_1473_28909.jpg

gallery_16287_1473_45964.jpg

gallery_16287_1473_38093.jpg

TBee Community Regular

TBee

Posted
  • Author
Posted

sorry, i relisted and i think km were in previous title. it's done 57xxx.

I've done hardly any kms since buying it but ive still done a couple services at Nissan to make sure it's all running perfect.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...