Jump to content
SAU Community

Recommended Posts

Hi guys, i'm clearing out my hoarded items that either came of my car or never made it onto the car....

I think i have a problem. Here's the items, photos are below.

-Prices are negotiable to a degree.

-Postage price is non negotiable, and is on top of the agreed price. I do not make money of postage.

If i charge an extra few $ on top of postage, its coz i have to find a box, pack it up and wait 40

minutes in my 55 min lunch break to send your parcel.

1 Surge tank to suit 2 bosch 044 pumps. has 2 x -8 JIC fittings to pumps,

2 x -8 on the side and 1 x -8 on top Price - $160

2 Foam Filled Plastic Fuel Tank, never used, conforms to CAMS regs i have been told.

has 2 x -8 JIC fittings for pumps and 1 x -6 for return on the top. - $200

3 6 standard RB25 side feed injectors out of car for about a year - $80

4 Rb25 manual series 2 ECU, will run S1 also - $50

5 Z32 Afm - unknown condition, didnt know i had it - $100

6 2 x sets of Rb25 Cams with cam gears and Solenoids - $75 a set

7 CAS for rb25, again didnt know i had it, comes with bracket, unknown condition - $75

8 RB25 Hydraulic lifters, set of 24, all good condition,

have sat in oil bath for close to 2 years.

didnt make noise when taken out of head - $50

9 Set of good condition std rb25 pistons, no marks on tops of pistons,no rings,

free conrods, conrods are rusted. $50

10 Rb30 crank - has been micropolished, kept this one as a spare in case mine

shit itself, hasnt happened yet, wont need it. $100

11 Chromed RB25 Intake manifold top. removed for plazmaman setup. excellent condition $50

12 3inch dump and frontpipe to suit lowmount KKR430 or kkr480 turbo,

partially heatwrapped. V band with clamp. $200

13 KKR style turbo HOUSINGS. front rear and CHRA. no shaft or blades.

bought as spare, never needed, sold turbo, buyer didnt want spares.

Comes with V band adapter. $100 for all of them

14 Compressor housing off a garret 35/40. 0.7A/R, with anti surge holes drilled.

decided against hacking it up to fit my engine bay. $200

15 Greddy Y-pipe with BOV return welded off. used for 3 dyno runs and

then changed to 1 big 4 inch filter. Was sitting around a bit i didnt wana sell it. $250

16 2 x Genuine Greddy Airinx air filters. 80mm tyres, never used. got wrong colour,

never returned as i bought from USA.both for $170 or $90 each

17 Rb25 O2 sensor. dont use it anymore. $20

18 RB25 VCT sensor, pulled off my head when i did the 30 conversion $50

19 Power FC Boost control solenoid, changed ECU's, was on a RB25 power fc.

only just got this back from the workshop, ecu sold a while ago - $300

OK, i think thats it for now. will add more stuff at a later date. Pictures Below

Contact me on 0401689894 via SMS, or PM (sms will get fastest reply)

Offers welcome

post-50733-1279716240_thumb.jpg

post-50733-1279716252_thumb.jpg

post-50733-1279716260_thumb.jpg

post-50733-1279716268_thumb.jpg

post-50733-1279716277_thumb.jpg

post-50733-1279716305_thumb.jpg

post-50733-1279716315_thumb.jpg

post-50733-1279716321_thumb.jpg

post-50733-1279716327_thumb.jpg

post-50733-1279716332_thumb.jpg

post-50733-1279716339_thumb.jpg

post-50733-1279716344_thumb.jpg

post-50733-1279716350_thumb.jpg

post-50733-1279716356_thumb.jpg

post-50733-1279716362_thumb.jpg

post-50733-1279716368_thumb.jpg

post-50733-1279716373_thumb.jpg

post-50733-1279716379_thumb.jpg

post-50733-1279716385_thumb.jpg

post-50733-1279716391_thumb.jpg

post-50733-1279716396_thumb.jpg

post-50733-1279716401_thumb.jpg

post-50733-1279716407_thumb.jpg

post-50733-1279716413_thumb.jpg

post-50733-1279716422_thumb.jpg

post-50733-1279716427_thumb.jpg

post-50733-1279716433_thumb.jpg

post-50733-1279716442_thumb.jpg

post-50733-1279716456_thumb.jpg

post-50733-1279716462_thumb.jpg

post-50733-1279716476_thumb.jpg

post-50733-1279716483_thumb.jpg

post-50733-1279716490_thumb.jpg

Edited by Gothik33
  • 2 weeks later...
  • 1 year later...

ANNUAL BUMP :domokun: :domokun: :domokun:

JUST BACK FROM OVERSEAS AND FOLLOWING ITEMS ARE STILL LEFT

4 RB25 manual series 2 ECU, will run S1 also - $50

7 CAS for rb25, again didnt know i had it, comes with bracket, unknown condition - $75

8 RB25 Hydraulic lifters, set of 24, all good condition,

have sat in oil bath for close to 2 years.

didnt make noise when taken out of head - $50

10 Rb30 crank - has been micropolished, kept this one as a spare in case mine

shit itself, hasnt happened yet, wont need it. $100

13 KKR style turbo HOUSINGS. front rear and CHRA. no shaft or blades.

bought as spare, never needed, sold turbo, buyer didnt want spares.

Comes with V band adapter. $100 for all of them $50

16 2 x Genuine Greddy Airinx air filters. 80mm intake diameter, never used. got wrong colour,

never returned as i bought from USA.both for $170 or $90 each $150 both, $75 each

17 RB25 O2 sensor. dont use it anymore. $20 $15

again, sms for inquiry about post, postage price based on location, 0401689894

Edited by Gothik33

I'll take the O2 sensor.

Brisbane 4073

PM me with the best way to pay you.

Cheers

SImon

ANNUAL BUMP :domokun: :domokun: :domokun:

JUST BACK FROM OVERSEAS AND FOLLOWING ITEMS ARE STILL LEFT

4 RB25 manual series 2 ECU, will run S1 also - $50

7 CAS for rb25, again didnt know i had it, comes with bracket, unknown condition - $75

8 RB25 Hydraulic lifters, set of 24, all good condition,

have sat in oil bath for close to 2 years.

didnt make noise when taken out of head - $50

10 Rb30 crank - has been micropolished, kept this one as a spare in case mine

shit itself, hasnt happened yet, wont need it. $100

13 KKR style turbo HOUSINGS. front rear and CHRA. no shaft or blades.

bought as spare, never needed, sold turbo, buyer didnt want spares.

Comes with V band adapter. $100 for all of them $50

16 2 x Genuine Greddy Airinx air filters. 80mm intake diameter, never used. got wrong colour,

never returned as i bought from USA.both for $170 or $90 each $150 both, $75 each

17 RB25 O2 sensor. dont use it anymore. $20 $15

again, sms for inquiry about post, postage price based on location, 0401689894

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...