Jump to content
SAU Community

Recommended Posts

sweet........

santa dropped by my place early this year :ninja:

most of my shiet have arrived.

big things such as exhaust/fmic ill get later on just before i fit the stuff up.

all i need now is ecu (tossing up between PFC or emanage), exhaust, fmic, & im done!!!!!!!!!

fuelpump, oil line & bleed valve/boost tee coming :laugh:

big thanks to all who supplied the parts to me;

justjap, rocket racing, niteworks, and users on sau.com & ns.com!

75ec1sj2.jpg

dpuo5.jpg

oilj2.jpg

oi2wb6.jpg

shsz0.jpg

strf9.jpg

st2qx2.jpg

tbim8.jpg

tthn8.jpg

And you're staying first quarter next year you'll have it all done?? Yeah Right!!! You won't last, you'll have all this in by xmas won't ya :D

I'm still finalising a few things but I'm hoping to have up n running this month in time for Xmas ;) Earlier would be better, should there be any other issues afterwards xmas wouldn't be the best time to sort them out lol

Can someone confirm the difference between an R34 4 Door Catback Exhaust and a 2 Door? One workshop tells me that they will be able to supply a second hand jap catback and that it won't matter if it's a 2 door? Or would they just customise it a bit? Oh that's another thing I don't have yet either..a turbo timer. I guess these can be easily added later though.

yeah turbo timers are easy to find for $50 & under.

4dr & 2dr catbacks are the same.

SSS autos in syd confirmed this for me.

and i found out that its the same in R32/R33's as well.

lol narh it will definately be next year, im saving up for PFC now..

let me know how u go with it ndawg.

got my turbosmart ultra gate & screamer today! WOOT!

niiiice!!! Well that clears things up then... I've seen exhausts listed as being for 2 door and others for 4 door specifically, but yeah now that I've got a second confirmation that makes things a bit easier with buying an exhaust now.

Hey Vikz...you still selling your zorst? hehehe

What's the difference between the N/A and GTT radiator? Is there much difference? I would to an extent base a decision on that. If Nissan have used the same radiator then go with that initially.

After doing the conversion, see how it goes with the stock radiator, and then make a decision whether to invest in an aftermarket radiator.

I never had any issues with overheating, to be honest the only time I ever saw the needle move from its normal position was in 38 degree heat in stationary traffic on Smith St after sitting there for 30mins

hey now i hope no one just tells me to read the full 19 pages which i did but wondering....

has anyone got a full list of the parts needed to do a turbo conversion to an rb25de?

gonna do it to my series 2 GTS4 and will make a full topic about with pictures and everything just need the full list of parts first thanks!

Also in this thread are some pics of the top of my engine using stock R33 parts for plumbing, you could get a custom made 90 degree with BOV flange made, that would be prettier :( Ignore the dirt, it had been sitting at the recovery impound yard for a bit.

http://www.skylinesaustralia.com/forums/R3...um-t243157.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...