Jump to content
SAU Community

From Only $350 Exchange Mail Order R33 R34 Factory Ecu Remap (after $100 Cash Back )


Recommended Posts




Only $350 Exchange Mail Order R33 Factory Ecu Remap (after $100 Cash Back ), R34 From only $450 exchange

R32 R33 R34 power fc and Real time ECU tune (R33 ECU use) in Sydney , please check this thread

http://www.skylinesaustralia.com/forums/Po...ml&hl=toshi


Please send your car modifications to me. I will remap chips according to your car modifications
and send it to you. Original chip will be replaced with remapped chip on ECU (R33 ECU use).



Please change colder spark plugs .

Please check and adjust ignition timing to factory timing.

When you get remaped ecu , please check Air/Fuel ratio and pingking on dyno for safety.

If Fuel is too rich or lean I will send another chip.


If you are not happy I will money back


3 stage maps available to suit your stage (differing in AFR (air fuel ratio))

Lean AFR will be powerful but cylinder will become hot causing over heating of the car.
Rich AFR will give you less power in comparison but cylinder will cool down by fuel and hence less dangerous for car.


Street and Quoter mile map AFR around 12. (removed all limiter)

We have 2 type street and Quoter mile map

A) Power will be around 200 kw (with FMIC) .Same fuel consumption Same stock fuel map under3000rpm and after4500rpm leaner than stock map.
Fuel consumption is same stock or better fuel. Timing map is totally different.

B) More power than A) by around 5-10kw.
Fuel consumption is bit less than stock map under 4000rpm.
Timing map is totally different.


We have 2 type Street and race circuit map AFR around 11.5 (not for drift)

A) Power will be around 195kw.(with FMIC) Same fuel consumption Same stock fuel map under3000rpm and after4500rpm leaner than stock map
Fuel consumption is same stock or better fuel. Timing map is totally different.

B) More power than A) by around 5-10kw.
Fuel consumption is bit less than stock map under 4000rpm.
Timing map is totally different


We have 1 type Race circuit and drift. AFR around 11

A) power around 190-195kw.



Please ask hiflow turbo and bigger turbo.

Z32 AFM , hiflow fuel pump and GCG hiflow turbo will be 220-260kw.


How to get $100 cach back:

a) UPLOAD to my thread
Either:
1.Difference in time during Quoter mile: std ecu and boost up VS. my ecu and boosted up(either by race track , yourself by hand or by PC)

2.Race circuit time std ecu VS. my ecu

3. Drift competition ranks

c) DO WITH FRIENDS
For those who book for two cars at the same time.

My customer got 207kw AFR 12 street chip A type

R33 GTST S1

split dump turbo-back exhaust with hi-flow stainless steel cat. Kakimoto racing muffler (very quiet)

splitfires, cold spark plugs.

FMIC

Greddy Profec Spec B- 12psi

Remapped ECU chip by Toshi

277hp -207KW

R33%20-AFR%2012%20207kw.jpg

  • 1 year later...

hey toshi

i have a r33 skyline its non turbo

currently running a turbo ecu

anyway of getting it remapped to non turbo a/f ratios

it has

extractors

2 1/2 inch exhaust with high flow cat

pod filter

walbro fuel pump

fuel reg

52mm dual core radiator

thats all motor wise

please email me as i need before christmas

[email protected]

thanks



  • Latest Posts

    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
    • With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
×
×
  • Create New...