Jump to content
SAU Community

Recommended Posts

  • Replies 107
  • Created
  • Last Reply

Top Posters In This Topic

ahaha nice thread david... bringing all the tree huggers n murders together... since we're all here now lets organise a picnic ill light the bbq with my fast and furious flames coming form my decat... n the that poxy tree hugger nic a31 can do the dishes.... let me know date and place????? who's in??? ooo wait my cars impounded n im goin court soon.. soo im gona need a lift? :/

post-76568-1285597799_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/page/6/#findComment-5468760
Share on other sites

Since I couldn't find it, I emailed EPA a while ago and finally got a reply.

Dear Nic:Your email was forwarded to an Officer in the Environmental Enforcement Unit of the Department, who has responded below; I trust this helps with your query:

The Commonwealth Motor Vehicle Standards Act 1989 allows for the Minister to determine national vehicle standards. Information about the Australian Design Rules and emission requirements may be found here and here.

In regards to offenses for removing a catalytic converter, Section 13A of the Motor Vehicle Standards Act 1989 provides offenses for the modification of a standard vehicle and making it non-standard, and applies a penalty of 120 penalty units.

The Commonwealth Crimes Act 1914 (Section 4AA) specifies a penalty unit to be $110, and thus the removal of a catalytic converter would carry a maximum penalty for an individual of $13,200. In relation to an offence by a body corporate, Section 4B allows for a court to issue a penalty of 5 times the amount of the maximum pecuniary penalty that could be imposed by the court on a natural person, being $66,000.

Settled.

Edited by Nic_A31
Link to comment
https://www.sau.com.au/forums/topic/335959-decat/page/6/#findComment-5471383
Share on other sites

I would like to see the figures for anyone who has actually received this fine in Perth, i recall this discussion on another forum a while ago.. i'd put my money on 0.

...even the inspectors @ pits will tell you to install a cat and come back again. Good scare tactic though!

Edited by endless
Link to comment
https://www.sau.com.au/forums/topic/335959-decat/page/6/#findComment-5471586
Share on other sites

Guest
This topic is now closed to further replies.



  • Latest Posts

    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
    • Very hard to make out what you mean, is it the squarish hole with redline shockproof (probably) under it? Is that pic from on top of the engine with the firewall to the left of pic and engine to the right? Either way, spray the area liberally with degreaser and try again, maybe circle the part you are worried about
    • Hey all, Noticed I have a hole on top of which im guessing is my transfer case/gearbox. I can see it from the middle of my firewall looking down. S1 R33 gtr Any advice or can pinpoint what this is/caused this?
×
×
  • Create New...