Jump to content
SAU Community

Compliance questions.

P1E

By P1E,
in General Automotive Discussion

 Share

Recommended Posts

P1E Mentor

P1E

Posted
Posted

I have two questions regarding vehicle compliance.

Firstly, if a dealer imports a Japanese car (not a personal import), is there any way the car can be registered without first being complied?

Secondly, is there a way to use a vehicle's registration number, engine number or VIN to find information on when or if it was complied in Australia?

Thank-you in advance.

Link to comment
https://www.sau.com.au/forums/topic/33760-compliance-questions/
Share on other sites
Kaido_RR Grand Master

Kaido_RR

Posted
Posted

If a vehicle was imported for race, is there any way it can be registered?

-No

Firstly, if a dealer imports a Japanese car (not a personal import), is there any way the car can be registered without first being complied?

-Nope not unless it is 15yr old (but that does required somesort of complied)

Is there any other explanation for a registered car (in NSW) not to have a compliance plate, nor a personal import plate?

-Yes it has never been compliance or wasnt not import as a personal import

FLO Collaborator

FLO

Posted
Posted
If a vehicle is imported for race/wreck, can it be registered?

Is there any explanation for a registered car (in NSW) bought from an import yard not to have a compliance plate fitted?

There are ways of doing it legaly, but can be alot of mucking around.I dont know about the car bought from the import yard ,sounds suss.I thought personal imports still had an aproval plate fitted.

P1E Mentor

P1E

Posted
  • Author
Posted

Hmm. I have a car without a compliance plate. I don't know whether it's missing or whether the car was in fact never complied, but the car is definitely registered. I am now attempting to transfer the registration from NSW to SA though, and I'm running into problems.

I have applied through Regency for an exemption, which they are fairly confident I will get, but I am more so curious as to why the car was ever registered by the NSW RTA without a compliance plate fitted.

I will call the Federal Office of Road and Safety during business hours on Monday and fire some questions at them.

  • 4 weeks later...
P1E Mentor

P1E

Posted
  • Author
Posted

FLO: Thank-you for your advice. I contacted the Federal Office of Road and Safety and my problems are now sorted. Let me buy you a beer if I ever meet you.

There is no legal requirement for a vehicle to retain a compliance plate after registration in NSW and mine was for one reason or another removed. DOTARS have approved the manufacture of a second compliance plate, meaning I will be able to (finally) trasnfer my car to South Australian registration and start spending money on modifications rather than interstate telephone calls to Government departments.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • Kinkstaah
      My BMW E39 528i touring

      By Kinkstaah · Posted

      @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...