Jump to content
SAU Community

Recommended Posts

my Nissan skyline 1993 r33 s1 skyline up for grabs . . . time to sell as im headed to south america in a month and have no money lol.

Tuning was done by status tuning which is now known as chequered tuning . . . last tune it pulled 260rwkw on 17 psi . . this car is clean. . most parts are 1000kms old.

engine:

un opened rb25det put in at 160,000 with only 88,000kms on it . . . now my car is on 189,000 kms. when the engine went in the 100,000 km service was performed.

t04e garrett turbo, just rebuilt less than 1000kms on it. turbo beanie sonic performance

high mount 6boost manifold 1000kms

turbosmart hyper gate 45mm . 1000kms

hks front mount cooler

turbosmart BOV stage 2

bosche 040 fuel pump

denson 550cc injectors

jjr coilpacks

3 inch dump pipe to 3 1/2 inch exaust with high flow cat to dual tip muffler

exedy heavy duty clutch

greddy profec b spec II electronic boost controller

apexi power fc with hand controller ( hand controller almost brand new )

z32 air flow meter

apexi air filter

hicas lock bar

(recently put all new exaust manifold studs and turbo studs)

interior:

leather inserts in door panels

sony explode speakers and cd headunit

specometer boost guage

new led's in cluster

exterior:

volks racing rims 17"

gtr front bar (near new)

gtr side skirts

gtr rear pods

sprayed calipers

new headlights

i have loved this car and taken great care of it since i got it 3 years ago . i have all the parts i have taken off for modifying in my shed. plus a front mount i was going to install which is much bigger and better. this is a bargain as i have receipts that add up to in excess $30,000 . . all the parts in my garage can go with the car. this car will not disappoint .

post-41795-1285136841_thumb.jpg

post-41795-1285136855_thumb.jpg

post-41795-1285136895_thumb.jpg

post-41795-1285136985_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/337811-r33-s1-skyline-1993-13500/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...