Jump to content
SAU Community

Recommended Posts

  • 2 months later...
Hi All,

Trying to track down a replacement rear brake light for the spolier (series 2).

An R33 Gts-t.

Regards

Rob

Hey Rob

Any luck on finding a rear spoiler light, becuase i need one for my S2?

Hi all,

As it turns out I took the brake light apart and re-soldered the blown resistor. Just replaced it with a paper clip and works fine...

Only hard part about it all was getting the red cover off the backing...... F%$KING nightmare.

Thanks

Rob

Ps. The series 1 brake light will not fit in a series 2 spoiler (already wasted $50 bucks on that.

Hi all,

As it turns out I took the brake light apart and re-soldered the blown resistor. Just replaced it with a paper clip and works fine...

Only hard part about it all was getting the red cover off the backing...... F%$KING nightmare.

Thanks

Rob

Ps. The series 1 brake light will not fit in a series 2 spoiler (already wasted $50 bucks on that.

Hey Rob :wavey:

You replaced the burned "resister" with a paper clip? Is that the best thing to do? Whats going to happen when a short or spick goes through the board?, what will blow out then?

It was a diod burned out on mine.

But getting it off was a nightmare. Better to fix it ur self then spend $100-$200 on a second hand one. And way better then spending $430 on an original one from NISSAN. hahah

i'm interested, how did you get the light open? i tried for a while and ended up cracking the red bit, so i gave up and just got a 2nd hand one.

Hey Terminal,

Just wondering how much did you pay for the second had one?

Anyway this is what i did to get the light open. I used a small flathead screwdriver and pushed it in in between the black and red plastic. Then i lightly twisted the screwdriver between the plastics to force it open. It's attached by some sort of glue. Continue doing this right around to remove the cover. It's a little time consuming but it will eventually come off and you will save cash in the process.

Most likely the diode has failed and it will need replacing. Make sure you test with a 9v or a 12v power supply before super-glueing the cover back on.

Hope the info helps :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a vb in honour of the car comming back
    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
×
×
  • Create New...