Jump to content
SAU Community

Cp Rb25 20thou Forged Pistons With Brand New Rings

Cupcake
 Share

Recommended Posts

Cupcake Collaborator

Cupcake

Posted
Posted

Ok so i need to raise some $$ for a bond on a house:

OLD THREAD SAID THIS

Hey, I've had this stuff sitting in my shed for awhile plan was to build a mental motor but an old car of mine is up for sale and I'd like to buy it back. Sooo these have to go.

Parts where purchased from Paul Diemar or Red R Racing and the setup was discussed with him and in his words was the best/toughest setup for a RB25

It consists of:

CP Forged Pistons 20thou oversized (86.5mm) with gudgeon pins and brand new rings - Note pistons are used but almost new removed from motor due to engine failure of some sort, Had them checked out thouroughly from a reputable engine builders he said they were mint and almost new condition.

RB26dett rods machined to suit rb25det, these have been known to take well into 700whp and Paul said that he favoured these rods over forged rods. Fitted with ARP 2000 Rod bolts

I am only looking to recover my losses to fund new project.

$1400 ono - will post anywhere at buyers cost. PLEASE DONT HESITATE TO MAKE ME AN OFFER. WITHING REASONABLE AMOUNT!

Pictures on request

NEW THREAD SAYS THIS:

$900 - I NEED THESE GONE ASAP!!!

Cupcake Collaborator

Cupcake

Posted
  • Author
Posted

soooo sick of f**king arounds, this is not boostcruising.com. Too many people telling me they are calling/coming/have cash/want/need/asap/very keen yet no one has fronted or come through.

this is f**king cheap as f**k. less than 1500 for a oversized forged bottom end complete.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...