Jump to content
SAU Community

Recommended Posts

Hi all,

I have for sale one immaculate as-new condition set of used Splitfire Direct Ignition Coil Packs.

post-46-1288307168_thumb.jpg

These coils are in perfect working order and have been used for 8,000 km's only.

Being the SF-DIS-001 type, they will suit the following:

- R32 GTS-T (RB20DET)

- R33 GTS-T (RB25DET Series 1)

- R32 GTR (RB26DETT)

- R33 GTR (RB26DETT)

These are not needed for my new car, so they need to go.

Im asking $440.00 Firm + Postage

Also for sale, is my excellent condition set of extremely rare and ultra expensive Genuine Mines Super Outlet Stainless Turbine Outlet/Dump Pipes for RB26DETT

These are about the best you can buy when it comes to RB26 dump pipes, with full stainless construction and nice big bellmouth type design for maximum flow.

No longer needed as moving to a single turbo setup

post-46-1288308835_thumb.jpg

These are worth close to $1400 new + Shipping.

I am asking $590.00 firm + Postage

Both items Located in North Sydney, and pickup can be arranged.

Thanks.

How do these compare with HKS Split dumps??

What size is outlet?

Are they a direct fit standard replacement? (As my exhaust is std dump back...)

Infinitely better than HKS, which are smaller and use a split wastegate pipe design. The weld and design quality is also second to none

These are comparable to Tomei, nice big and free flowing.

If you were going to fit dumps its a good idea to fit front pipes at the same time.

I am pretty sure they are 70mm outlets but I will try and find a ruler to verify

I have HKS 67mm twin Exhaust (one exhaust for each turbo) from front pipe back currently suited where the std dump line up, not souch concerned woth size more so how it replaces cos i really dont want to replace my beloved exhaust...

would like something more free flowing as upgrading to -5s from R34GTR Turbos on my R32 GTR...

split dump (free flow) vs bell mouth design (turbine/wastegate turbulence)...Im still not sure which direction or if information ive been provided with is valid or not...

your dumps look closer to 70mm than 67mm does the reduction have a further negative effect???

  • 4 weeks later...
  • 4 weeks later...
  • 2 months later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...