Jump to content
SAU Community

Recommended Posts

The time has almost come for me to let go of my pride and joy that has completely consumed my life over the last 4 years. The decision has been extremely difficult as I absolutely love this car but after re-evaluating my life and the direction I want to go in there is no longer room for the car due to financial constraints and also I will be relocating next year. This car has had so much time and love put into it and has been built from the ground up by Unique Autosports in Western Sydney. No short cuts have been taken on this project and the car has been well looked after since day 1. Car is always garaged and never thrashed or raced. Over $45,000 (have all receipts) has been spent getting this car to where it is. No time wasters please.

Ok where to start! I have owned this car for 2 years now, and it was a completely stock rolling shell when purchased with 110,000kms on the clock. Before the engine was dropped into the current shell, I had the engine built for my old 1991 Black GTST. I have put 30,000kms on the rebuilt motor. Car is now rarely driven and spends most of its days in the garage. The car has been engineered so new owner will have minimal problems with the authorities.

Serviced every 5,000kms with Motul Chrono 300V Engine Oil. All other fluids are high temp Elf/Redline and have been changed regularly. Engine currently has a very mild tune and puts out 230rwkw at 15 psi (A LOT more potential with further work and more boost)

Make: Nissan

Model: Skyline R32 GTST

Engine: Forged Built RB25DET Neo S1 (out of 1998 R34 GTT)

Year: 1992

Km's: 128,000kms (rebuilt engine has 30,000kms)

Location: Blue Mountains, West of Sydney

Colour: Custom Velocity Blue (Has light pearl through paint)

Rego: until May 2011

Transmission: 5 speed manual

Price: $20k ONO

Contact: PM or post in thread. Will give Mob number upon PM request.

MOTOR/ENGINE BAY (Built by Andrew and Ben @ UAS)

*ACL Racing Forged Pistons and Rings (20 thou)

*Honed Rods

*Fully Prepped block (all the usuals - NO shortcuts)

*Bored and Honed Block

*Fully Balanced

*Metal gasket kit

*Bronzed valve guides

*Linished crank

*N1 oil and water pumps

*Head has been ported and polished

*630cc Nismo Injectors

*GTR fuel pump mounted in tank (fairly quiet)

*Greddy Oil catch can

*Custom manifold (heat wrapped for lower temps)

*Turbosmart 45mm external wastegate

*GT35/40r Turbo (Garrett) Custom built by GCG - 0.63 rear housing

*Alloy radiator (40mm and brand new)

*FMIC with alloy piping for more effective cooling

*Splitfire Coilpacks

*Turbosmart Supersonic BOV (sleeper series black and plumbed back)

*DIA specialised air induction POD by BMC (enclosed)

*Braided lines and fittings everywhere

*Hyperformance Marine Battery

WHEELS

*Lenso GT5’s 19x9 (front) 19x9.5 (rear) with about 95% tread (235 fronts and rears)

DRIVELINE/SUSPENSION/EXHAUST

*Suspension kit is a full Whiteline works package with swaybars, Bilstein shocks, lowered springs, alignment bushes etc.

*HICAS locking kit

*Standard R33 RB25 gearbox (new gaskets/seals/bushes/bearings)

*Full 3 inch mandrel bent turbo back exhaust system with Cat

*Diff is Modified and LSD

INTERIOR/ELECTRONICS

*Brand new Turbosmart E-Boost 2 Electronic Boost controller (Set at 5psi, 10psi and 15psi)

*Microtec MT8 Ecu

*Boost, Oil Temp, Oil Press gauges (autometer cobalt series)

*HKS Turbo Timer

*Pioneer Bluetooth/MP3 head deck

* Genuine Momo Italia Steering wheel

* Custom Chrome Gear knob and leather handbrake/gearstick boots

* Tinted windows

EXTERIOR

* GTR front bar with N1 Slots

* GTR side skirts and rear pods

* All guards have been rolled to accommodate the wider Offset of wheels

I am sure there is more, but that is the major stuff and I will list anything more when I remember

There is a range of spares and stock parts that will go with the car and the new owner is quite welcome to take it all away.

Will get some more pics up this weekend, plus interior pics.

post-23286-1288696944_thumb.jpg

post-23286-1288697002_thumb.jpg

post-23286-1288697049_thumb.jpg

post-23286-1288697112_thumb.jpg

post-23286-1288697223_thumb.jpg

post-23286-1288697304_thumb.jpg

post-23286-1288697349_thumb.jpg

post-23286-1288697370_thumb.jpg

post-23286-1288697419_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/342822-forged-rebuilt-r32-for-sale/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 1 month later...
  • 2 weeks later...
  • 2 months later...
  • 1 month later...

BUMP and PRICE DROP!

Need to sell the car urgently as I am moving on the 2nd of August this year.

15K!!!! ONO.

Car is currently unregistered due to it sitting in my garage but can be re registered for the new owner if interest is shown. Car is also up on Carsales.com so be quick.

Price is somewhat negotiable but be realistic considering the time and money already spent on this car. 15k is an absolute bargain!

Any enquiries just pm or text/call me.

Thanks guys!

Luke

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...