Jump to content
SAU Community

Recommended Posts

Time for a change, owner of this vehicle for the past 3 years. Bought as stock standard car. Tasty mods with potential 270Kw with upgraded injectors.

Reason why i'm selling this car is because I have upgraded to a modified s15, something different...

Year: 1996 Series 2

Km's: 160XXX

Location: Melbourne

Colour: White (Brand new paint)

Rego: ADIS (till 11 AUGUST)

Transmission: 5 speed manual

Price: $10K ono - I have spent more than $10k in mods alone.

Contact: SMS 0421 864 698 /PM or post in thread

Power: 230KW @ 14psi

list of mods:

Motor/Engine Bay

* High flow G2 500HP turbo ($1370) HYPERGEAR

* Nistune Z32 ecu tuned by DR DRIFT ($1100)

* Splitfire coilpack($550)

* Bosch Fuel pump ($300)

* Blitz Pod filter with custom 3inch intake ($300)

* Front mount intercooler,return flow. Tanks are HKS ($300)

* Turbotech boost controller T set to 14psi ($30)

* Full exhaust with twin tip at the end ($500)

* Exedy heavy duty cushioned button clutch ($900)

* Brand new O2 sensor($90)

* Brand new fuel filter ($40)

Wheels/Suspension/Exhaust

*350z Wheels with Toyo rubber-225s ($600)

*Tein height adjustable coilovers ($800)

*Full exhaust with twin tip at the end ($500)

Inside the Cabin

*Boostgauge/oil gauge with Apiller ($120)

*HKS turbotimer ($60)

*Nismo Gear nob ($50)

*JVC mp3/ipod/usb player($350)

*Pioneer 6"front+rear speakers ($200)

*Rear Skyline floor mats

Exterior

*Fiberglass Bootlid, no spoiler or holes ($300)

*Professionally tinted windows ($300)

*Brand new paintjob ($3000)

Stock parts available:

* Stock exhaust

* Stock intercooler+piping

* Stock Air Filter box

Car service:

*General service done 3K ago

*Front brake pads changed last week ($100)

Note: Compression test was done last year with 155 accross all 6 cylinders. Any test welcome. No time wasters or low ballers but reasonable offers WILL be considered.

Note: Bootlid does not sit flush and is not a perfect fit and not a perfect colour match. Therefore if the car is sold i will re paint the boot or supply a perfect standard series II boot with spoiler.

The car will be listed on CarSales and other websites. Thanks for looking.

111cuo.th.jpg

aaaaaaaaaacs.th.jpg

222tk.th.jpg

333y.th.jpg

444vmq.th.jpg

555gd.th.jpg

666q.th.jpg

Link to comment
https://www.sau.com.au/forums/topic/343817-1996-r33-turbo-series-2-230kw/
Share on other sites

Last time I changed my mind about selling a good car but this time I'm serious. I have already purchased my new car therefor I'm looking to sell asap to the right person. Pictures of engine bay will be up tonight.

Car uses 11L/100km so great economy to power ratio.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...