Jump to content
SAU Community

Recommended Posts

Leftovers from wrecking r33 series 1.5 all parts located in sa adel hills. clearing out for room.

lhs front gaurd $50

rhs front gaurd $50

rhs front headlight $50

gaurd orange indicators $10 pair

dash missing two small vents on top $80

center consol 40

heater/aircon control $40

heater $80

entire floor carpet $50

roof lining $20

center roof light $5

map lights $10

holy shit handles on roof $5

lhs a pillar $10

speedo cluster $80

glovebox $20

rhs sun visor $10

rear lhs tail light $80

passengers door$100 with all electrics

door linings and electrics can be separated along with mirrors

side skirts (one broken in half) $30 pair

windows (remove yourself or get removed properly) $$$

3"catback exhaust with emptied cat and rear cannon $200

interior lining $50

parcel shelf $20

boot lining $40

boot seal $15

bonnet latch $30

horn $10

fuel tank $50

rear skyline strip between lights $40

scuff panels inside doors $20 pair

fuel cap covering panel $10

windscreen wiper stalk $10

indicator stalk $10

steering column $20

rear rotors and calipers $150

front 5stud hubs $100 pair

standard diff $150

front suspension $50

rear subframe $200

r32 rear spoiler mspec 40$

r34 gtr front indicators (orange) $40 pair

r34 side indicators $20 (orange)

0419837474 prefer sms or call as apposed to pm, thanks

  • 2 weeks later...

rear rotors and calipers sold

subframe sold

sideskirts sold.

rest offers on the lot, all taking up space. also brake booster availble too.

whats with getting text messages at about 4 in the morning after car parts......do people really sit on here and browse this early?lol....anyways still few bits to go..just using up room now..

  • 4 weeks later...

do u have passenger door for the 33 still ,if so how good is it paint ,dents,rust etc as i am pretty fussy thanks Darren

do u have passenger door for the 33 still ,if so how good is it paint ,dents,rust etc as i am pretty fussy thanks Darren

yep i just removed it then. i couldnt find any dents or rust on the door. the triangle section where the side mirror is inserted however has rusted, its not visible when the mirror is in, so if you were to treat it and apply an undercoat its not going to affect what you see anyway as its hidden.

the rest of stuff i really want gone so open to offers.

the shell has been sold sowhat i have listed in origional post is all available, prob a few bits gone since.

the entire steering rack i pulled out thismorining- also heater unit. (please no msgs like "will u post steering rack to syd for $100 inc postage" because no i wont. postage alone is probably more than 100$ so please no time wasters like i have previously"

so ...bump to see everything gone

Hey

is the mspec spoiler like a standard gtr one? (forgive my ignorance)

thanks

hey

the gtr spolier is not the same as the mspec. gtr spolier is u shaped and does not have a center connction to the boot. the mspec one i have connects at both ends of the boot and also in the center and is really only about a cm maybe a touch higher gap between spolier and boot. it also has a brake light inbuilt into it. which if you dont like can fibreglass up. if you want a photo sms me and il mms a photo through.5114250195_c60415c9ec_z.jpgthis is like the spoiler i have, in undercoat,

90blackgtst32.JPG gtr spolier

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...