Jump to content
SAU Community

Recommended Posts

post-51163-0-13620700-1293758719_thumb.jpg

Nissan Skyline, R33 Series II, 1996

Interior still A1 seats all good no interior been stripped,

Front bar not on photos but will go in sale

Ok lots and lots of mods forgive me if i forget some below"

-Aftermarfket forward facing plenum custom

-Z32 Air flow meter

-HKS gate with screamer

-Slotted front roters with new rear bendix brakes

-Flared and rolled rear guards

-Big FMIC custom stainless piping

-HKS coil overs

-3" exhaust system

- Access tuned Apexi power FC with hand controller

- Momo aftermarket racing wheel

-Apexi power intake air pod

-Cusco and HKS sway bars front and rear

-Aftermarket oil catch can

-Built RB25 motor done hardly any k's

-Bosch 040 fuel pump

-Greddy dual stage boost controller

-HKS turbo timer and secondary boost guage

-Garrett aftermarket huge will update type later

-HKS bov

-Bayside blue with fibre glass kit

-Heavy duty clutch

-New 25 Gearbox

-550 Nismo injectors and fuel rail

-18" Wheels loads of dish

-Nismo clear side indicators

-Tuned by Boostworx running 271.5rwkw on 14psi safe range has heaps more in reserve

-New Bendix brakes as of 27/12/10

Contact me on 0431-388-718 or pm me

Car is in Adelaide can be sent to all states

It is defected for to low to loud and the top mount turbo didn't help haha

NO LOW BALLERS!

post-51163-0-56573400-1293759436_thumb.jpg

post-51163-0-68742400-1293759659_thumb.jpg

post-51163-0-40554200-1293759961_thumb.jpg

post-51163-0-30144800-1293760160_thumb.jpg

post-51163-0-37632200-1293760523_thumb.jpg

Edited by sus34
Link to comment
https://www.sau.com.au/forums/topic/348813-r33-series-ii-899000-heaps-of-fruit/
Share on other sites

Yeah but I wouldnt buy a car interstate without seeing it in person, just a big hassle... and I'd have to get this blueslipped etc, i.e returning it to stock for it to pass.

Im spewing though, such a nice car, value for money

goodluck

Edited by TONTON

only thing coppers could pick is the topmount and if it has coilovers , borrow a standard lowmoint setup and dummy the intercooler piping and then chuck it straight back on still a mega bargain!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
    • -10 is plenty for running to an oil cooler. When you look at oil feeds, like power steering feeds, they're much smaller, and then just a larger hose size to move volume in less pressure. No need for -12. Even on the race cars, like Duncans, and endurance cars, most of them are all running -10 and everything works perfectly fine, temps are under control, and there's no restrictions.
    • Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
×
×
  • Create New...