Jump to content
SAU Community

Boost Issue

Tool

By Tool,
in Engines & Forced Induction

 Share

Recommended Posts

Tool Newbie

Tool

Posted
Posted

Sorry if this has already been asked before, I searched but was unable to find anything on this issue. I have an R32 GT-R running a Power FC and it will only ever reach 7lbs of boost even though it's set to 20lbs, is this possibly due to a 'limp home' mode or something of the sort? There doesn't appear to be any leaks and I've checked through the hand controller and all the settings appear to be the same as they used to be. The knock sensor is registering higher than previously was but nothing overly worrisome. Any thoughts appreciated. Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/349138-boost-issue/
Share on other sites
doo doo Proficient

doo doo

Posted
Posted (edited)

What sort of boost controller you're using will be handy to know-( eg. if you have a blitz SBC i-D set to 20 in manual mode it's a percentage, not a psi level) although 7 psi is pretty low?- Have you checked this boost level with a gauge that's know to be accurate?

Edited by doo doo
Link to comment
https://www.sau.com.au/forums/topic/349138-boost-issue/#findComment-5610769
Share on other sites
Tool Newbie

Tool

Posted
  • Author
Posted

assuming its a power fc boost control kit? is it still turned on in the etc menu? afaik theres no limp mode in the pfc, its pretty basic.

checked the solenoid works?

It's a Greddy E-01 boost manager, adjusted the solenoid and all it did was mess with the idle. It still caps out at 7psi.

Link to comment
https://www.sau.com.au/forums/topic/349138-boost-issue/#findComment-5612144
Share on other sites
Tool Newbie

Tool

Posted
  • Author
Posted

The power fc wont do that, It will cut the engine if you go over your set boost level (with the boost sensor enabled and connected)

What boost controller are you running? have you got it set right?

Greddy E-01, haven't consciously changed any of the settings since it was tuned and I don't leave the remote plugged in to prevent accidental changes.

Link to comment
https://www.sau.com.au/forums/topic/349138-boost-issue/#findComment-5612150
Share on other sites
Tool Newbie

Tool

Posted
  • Author
Posted

What sort of boost controller you're using will be handy to know-( eg. if you have a blitz SBC i-D set to 20 in manual mode it's a percentage, not a psi level) although 7 psi is pretty low?- Have you checked this boost level with a gauge that's know to be accurate?

I have an analogue gauge plugged in which appears to reflect the same boost.

Link to comment
https://www.sau.com.au/forums/topic/349138-boost-issue/#findComment-5612153
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      Ok so will run the piping over that radiator and no plenum it is. Put that money towards a Haltech and see what suits. Any ideas something like an elite 2000 or 2500 right? My long term goal is 300kw e85 and manual swap and that’s a dream come true. For now will be 200kw and auto the stock rb25det neo intake isn’t too expensive with throttle body. If I was to have the port matching done, Would that be better than the stock de intake as the det has bigger holes plus has the spots for sensors etc? And suit more long term?  appreciate the advice?   
    • MBS206
      R33 GTR running -9 with no tune

      By MBS206 · Posted

      You understand AFR is not the only thing that contributes to it pinging yeah? Funnily, what the AFR gauge will tell you when it likely is pinging, is going to make you think things are really safe and good.
    • MBS206
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By MBS206 · Posted

      Run the piping how we all have for decades. Also the duel runners with the +T setup dramatically helps it gets on boost quicker. Yes, chase huge power it'll become a problem, but you're a long way off when you're already saying an aftermarket ECU is out of the budget. You also say NisTune as it's simple, and then immediately say it'll be painful, meaning... It won't be simple. It will likely cost you a lot more stuffing around with a Nistune, than just putting a Haltech or similar in.
    • 677_GTR
      R33 GTR running -9 with no tune

      By 677_GTR · Posted

      I’ll order an afr gauge to keep an eye on it.  Then will get a haltech soon 
    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      TD05 or maybe pulsar PSR2867r Gen 2?  id love a garret but it’s quite out the budget for now and I’m not chasing crazy power.    yeh fuel pump haven’t looked into but whatever works, kind of last on my list.    Nistune because it’s simple but Ik it’s a lot of pain especially as I’m auto +t with the whole seperate TCM etc still investigating that. Haltech id love but once budget tight for now atleast.    finally the reason I’m trying for a plenum instead of the stock intake is I already have a standard Intercooler mounted etc. so the ports are on both sides so trying to not have to go over the clutch fan radiator etc. trying to find a good deal return flow if I don’t than this will do for now I guess. btw any ideas with that, apparently some people have to cut blades to reduce it from hitting the Intercooler piping over the radiator ? Thanks 
×
×
  • Create New...