Jump to content
SAU Community

Carbon Fibre Wrap?

calebR33

By calebR33,
in Exterior & Interior Styling

 Share

Recommended Posts

calebR33 Community Regular

calebR33

Posted
Posted

I have a car in mind that i want to buy and have gone to test drive it today. I like the car but i realised that parts of the dash have been wrapped in the carbon fibre thing that many people are talking about. Only issue is that there are bubbles in many places and it seems to be coming off. Generally it looks really dirty. Does anyone know how to remove it ?

Link to comment
https://www.sau.com.au/forums/topic/349508-carbon-fibre-wrap/
Share on other sites
Husky33 Veteran

Husky33

Posted
Posted (edited)

a heat gun should work fine, are a blowdryer.

Heat it up a little so the glue underneath melts, then it should peel off, might have to use a plastic spatula or something.

Citrus spray will help get remaining glue off.

Edited by 180_mph
Waxhead Community Regular

Waxhead

Posted
Posted

If i just heated it up... it wouldnt just come off perfectly right ? scared that there will be bits of glue stuck :S

If it is the 3M stuff, should come off without leaving any (not much anyway) residue. Heat it with a blow drier and peel it off. I have applied this stuff to some of my car interior, and when not happy with the first application, heated it up and removed ,then re-applied again. Left no residue (glue etc) when I did it.

The citrus spray is just a cleaning product ,can be found in most supermarkets next to the spray and wipe etc.

RusH_ Veteran

RusH_

Posted
Posted

a heat gun should work fine, are a blowdryer.

Heat it up a little so the glue underneath melts, then it should peel off, might have to use a plastic spatula or something.

Citrus spray will help get remaining glue off.

If it is the 3M stuff, should come off without leaving any (not much anyway) residue. Heat it with a blow drier and peel it off. I have applied this stuff to some of my car interior, and when not happy with the first application, heated it up and removed ,then re-applied again. Left no residue (glue etc) when I did it.

The citrus spray is just a cleaning product ,can be found in most supermarkets next to the spray and wipe etc.

These guys hit the nail on the head,

The issue is, with that type of vinyl, it has a lower adhesion that others due to the pattern and (if its the one im thinking of) the honeycomb effect on the back designed to make application easier.

When the vinyl is stretched to conform to curves and such, it loses a portion of its adhesion, which can cause it to pop up when exposed to high temperatures such as those experienced in a car on a warm day when the windows are up. This is usually counteracted with a small dose of adhesive promoter/primer to add that extra 'stick' around areas where the vinyl has been stretched.

Should come off fine with the above methods :thumbsup:

RusH_ Veteran

RusH_

Posted
Posted

Chances are the vinyl will have already lost its adhesiveness since the install, so its unlikely youll be able to remove the bubbles, its ok to pop them and push outthe air when you first do the install but over time it loses its adhesion.

Sadly its probably time to re wrap it

  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...