Jump to content
SAU Community

Recommended Posts

i have heard of people finding their steering to be heavier after fiting the lockbar but then there is no movement in the rear wheels anymore

when i fitted the lockbar i went down and got a four wheel allignment and afterwards found the car to be more predictable when cornering under power (in a controlled enviroment of course) and noticed no difference to the feel of the power steering

the only thing that changed was the hicas light stayed on easily fixed by removing the globe

have a look in the diy section of the forums im sure all this will have been covered along with a guide on how to fit the lockbar

Link to comment
https://www.sau.com.au/forums/topic/349609-hicas/#findComment-5616168
Share on other sites

On the 32's, the HICAS was a hydraulic system running off the same power steering pump, etc as the front steering.

On the 33's, it's a fully electric system, completely separate from the front power steering, so unless someone stuffs something up terribly, your standard power steering won't be affected.

Link to comment
https://www.sau.com.au/forums/topic/349609-hicas/#findComment-5617663
Share on other sites

33s have speed variable power steering , softer at low km , harder at high km

depending on how hicas is cancelled you will lose the variable part and only have the harder setting

R32's have the speed sensitive steering too.

Heavy steering is usually a HICAS fault, common causes are removal of the HICAS control unit and incorrect alignment of the clock spring behind the steering wheel (steering angle sensor).

P.S. ditch HICAS, the car will be more predictable and safer on the edge.

Link to comment
https://www.sau.com.au/forums/topic/349609-hicas/#findComment-5624686
Share on other sites

my hicas seems to be a little bit weird... does it's check sometimes when im just cruising down the road (happened both times around doing 60km/h)

which in turn makes the butt end of my gtr shake and is quite a dodgy feeling when your car does that... is it easy to still remove hicas on 33gtr's? same business or a little different?

Link to comment
https://www.sau.com.au/forums/topic/349609-hicas/#findComment-5629761
Share on other sites

super hicas, hicas, its all the same shiz, there are few ways of doing it tho, some ppl are happy jsut to put in a lock bar, some ppl remove the whole system lines, fuse/relay etc

u can buy shitty chinese ones, or for about $50-$80 more u can buy urself a good one.

talk to Jeremy at styled 2 race he got me in my whiteline one

Link to comment
https://www.sau.com.au/forums/topic/349609-hicas/#findComment-5630570
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...