Jump to content
SAU Community

Recommended Posts

An all time classic Volk, forged monoblock - super lightweight and strong, massive brake clearance for those with big brakes. These will never go out of style. 18 x 9 +35 front and 18 x 10 +35 rear

Import monster had them $2300 for a complete set if you check out this link http://www.importmon...products_id=919

unfortunately it only comes wit x2 of 18x9 front and x1 18x10 rear, which is not a complete set. It will be a very cheap buy if you can find the other rear 18x10,

They dnt have buckles, but with slight scrathes

IMAG0102.jpg

IMAG0101.jpg

IMAG0100.jpg

IMAG0099.jpg

IMAG0106.jpg

IMAG0105.jpg

IMAG0104.jpg

IMAG0103.jpg

Make an offer, no stupid offers please, resonable offer will be considered

contact me: 0400 928 949 or pm me here or email me on [email protected]

pick up location: Western Sydney near to WSID (rooty hill)

*******************************************************************************************************

Front and Rear Strut bars up for sale for Mark IV SUPRA

IMAG0110.jpg

IMAG0109.jpg

IMAG0108.jpg

$60 each

or $100 for both

contact me: 0400 928 949 or pm me here or email me on [email protected]

pick up location: Western Sydney near to WSID (rooty hill)

******************************************************************************************************

Link to comment
https://www.sau.com.au/forums/topic/350832-nsw-volk-rims-supra-strut-bar/
Share on other sites

more items for sale:

Up for sale Skyline R32 Vertex Style, a pair of Side skirt and rear bar for GTS/GTS-T/GTS4

Good condition slight scratches but might need a good respray to suit your car's colour

Reason of selling: Garage clean up

IMAG0092.jpg

IMAG0188.jpg

66550667AHFUYtY4R32VTSSRB.jpg

$350 ono

contact me: 0400 928 949 or pm me here or email me on [email protected]

pick up location: Western Sydney near to WSID (rooty hill) / HIlls district

***************************************************************************************************

Stock Airbox for R32 GTS-T/GTS4 Rb20det

IMAG0189.jpg

comes with filter aswell,can become handy for roadworthy and to remove defects if your pod filter has been defected.

$40

Contact me: 0400 928 949 or pm me here or email me on [email protected]

pick up location: Western Sydney near to WSID (rooty hill)

*************************************************************************************************

16 inch Genuine Enkei Bortex Mirella made in japan multi stud 4x114.3 and 5x114.3

16x7 wide and the tyres are 205/50/16 all around

2 wheels has 95% rubber and the other 2 are 80% rubber

Good condition no buckles but with slight scratches

IMAG0185.jpg

IMAG0186.jpg

IMAG0187.jpg

DSC01490.jpg

15864_219312209618_621974618_4204020_1591911_n.jpg

$600 ono

Contact me: 0400 928 949 or pm me here or email me on [email protected]

pick up location: Western Sydney near to WSID (rooty hill) / HIlls district

Edited by GGGTS4
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...