Jump to content
SAU Community

Sr20 Conversion?

200sxs13

By 200sxs13,
in Four Door Family & Wagoneers

 Share

Recommended Posts

200sxs13 Apprentice

200sxs13

Posted
Posted

Hows things fellas,just wondering could someone tell me what modifactions need to be made when doing an sr20det conversion on a A31....im currently doing this and im looking for info on what needs doing,somethings i have noticed are the rb has a mechaincal speedo wear as the sr box has a electric{wire and plug}how do you get around this,also there are to other plugs on the gearbox which i havent a clue what there for?does engine mouts have to be modded?drive shaft does that have to be modded?does water lines.heather lines ect have to be modded,as much info as possible please guys thanksyes.gif

Link to comment
https://www.sau.com.au/forums/topic/355144-sr20-conversion/
Share on other sites
daisu Mentor

daisu

Posted
Posted (edited)

I have an SR20 in my cefiro.

Use a silvia front crossmember.

Radiator will need to be from an S13/180sx or you can use an RB series radiator if you extend the top radiator hose to the other side.

have read that some combination of gearbox crossmember will fit but I couldn't figure it out, just modified my current one.

Can't remember exactly about the tailshaft, I think if you unbolt them at the center bearing and swap the front half over it works.

heater lines are just rubber hose, you can easily make it fit.

Needs a few wiring modifications but I didn't do the work so can't tell you there.

I would definitely do this conversion again to R32/cefiro/laurel, the RB20 just doesn't compare.

Edited by daisu
Link to comment
https://www.sau.com.au/forums/topic/355144-sr20-conversion/#findComment-5688288
Share on other sites
200sxs13 Apprentice

200sxs13

Posted
  • Author
Posted

I have an SR20 in my cefiro.

Use a silvia front crossmember.

Radiator will need to be from an S13/180sx or you can use an RB series radiator if you extend the top radiator hose to the other side.

have read that some combination of gearbox crossmember will fit but I couldn't figure it out, just modified my current one.

Can't remember exactly about the tailshaft, I think if you unbolt them at the center bearing and swap the front half over it works.

heater lines are just rubber hose, you can easily make it fit.

Needs a few wiring modifications but I didn't do the work so can't tell you there.

I would definitely do this conversion again to R32/cefiro/laurel, the RB20 just doesn't compare.

sounds good dude thanks very much...about the front cross member i taught sr20 drop straight into skylines so would it not drop straight onto the cefiro mounts?also the the 2 little pin type mounts on the end off the sr rad,do they sit into the original cefiro holes on the support legs?A manual cefior mount is the same as an s13 so it should work on the same mount if you have a manual cefiro which i do?

Link to comment
https://www.sau.com.au/forums/topic/355144-sr20-conversion/#findComment-5688841
Share on other sites
daisu Mentor

daisu

Posted
Posted

My understanding was that the SR conversion requires the crossmember from a silvia even if it is going into a skyline. Perhaps you can use custom mounts or something otherwise.

Cefiro's are funny with gearbox mounts. I used an S13 manual gbox crossmember to convert my originally auto RB20 to manual, but the same crossmember didn't work so well with the SR conversion. If your cefiro is factory manual then the case may be different.

Link to comment
https://www.sau.com.au/forums/topic/355144-sr20-conversion/#findComment-5690675
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...