Jump to content
SAU Community

Recommended Posts

Hey all,

I have changed my mind and decided to sell my R33 instead of replacing the engine.

It's a 1993 R33 GTS series 1 with a suspeced spun bottom end bearing

asking 5K neg

ENGINE/DRIVELINE/ETC

  • Factory manual
  • Heavy duty clutch
  • Catback exaust with 3" cannon exaust
  • Engine oil & oil filter changed every 5,000-7,000 km
  • Gear box oil just changed
  • Brakes fluid just changed (inc bleading of all lines all the way through)
  • Recently changed radiator fluid
  • 18*,***kms (mostly highway, I live in Whyalla)
  • King Lowered Springs
  • KYB shock (less then 10,000kms old)

EXTERIOR

  • Full viva garage type 2 bodykit (light damage to front bar, nothing structural to the car)
  • 25mm flared guards front and rear
  • re-spray in blaze blue (outside and door jams only)
  • Xennon lights (low beam)
  • stock rims with near new tyres, can arrange 17" ROH rims with near new tyres for a bit more (cannot remember tyre type but about 250-280 ea)

INTERIOR

  • Very good condition, besides wear on right side of drivers seat and wear on handbrake "grip"
  • Genuine skyline floor mats (all 5)
  • Average sound system; 4" JBL parcel shelf, clarion cd player
  • Momo steering wheel with boss kit
  • Isotta shifter
  • Climate Control globes replaced with white 40,000MCD LED's (very bright white light)
  • Ignition light also replaced with 40,000MCD LED

THE BAD

Knocking noise from engine, 90% sure its a big end bearing. has not been driven since the noise started

slight power steering leak, one of the seals in the pump is on it's way out

flat battery, car has been sitting there for a couple of months

This car would either be great for someone as a first car or someone on their p's, although a new engine or a bottom end rebuild will be required.

Also would make a good shell if you have written off your R33 and just need to transplant parts.

Or just make some cash and either replace the engine or part it out

May be able to drop the price a little if you don't require the gearbox.

The car is currently located in Whyalla SA, can transport to adelaide at your expense

Best bet would be to text me on 0407971706

Cheers Luke

Pictures will be up 2moro

Edited by 2FST4U.R33
Link to comment
https://www.sau.com.au/forums/topic/355848-r33-gts-for-sale-in-sa/
Share on other sites

  • 3 months later...

Hey Champ,

Im interested in your car im a mechanic. I do alot of work on skylines.

The whole engine and drive line will need a rebuild.

make me a good offer without the gearbox and that.

Im after a shell to build a beauty.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...