Jump to content
SAU Community

Recommended Posts

Got a 2000 model skyline gt manual with the rb25de neo for sale. Non turbo.

Got damage to front and small amount to rear. Front has hit the rad support slightly and smashed both headlights. Will need to replace front bar (may be able to be fixed, is broken along bottom, headlights, rad, fans, bonnet. Engine still runs, very small leak in radiator. Fan not touching radiator though. Has battery but is on charge atm, not sure if it is stuffed, not very old though. Front quarters are undamaged.

Chassis is all straight. Rear has also been touched, will need to replace boot lid, but spoiler is fine and bumper may be ok. Car has only done 104 ks. Has cannon muffler and apexi pod filter. Also has an alpine headunit with parrot bluetooth integrated, front usb, ipod cable connection etc worth bout $400. Has factory floor mats.

In decent nick, low k's, cigarette burn to rear passenger side seat base but other than that, pretty clean. Tyres are good with rears near new, has the factory rims.

Im happy to sell manual conversion including everything required.

ALL PARTS AVAILABLE. Let me know what you need and feel free to make non stupid offers for stuff!

Located near Frankston, VIc. Viewing welcome. Please contact 0422641010 for more info or to see the car.On a last note, Dont call after 10 at night, thanks

Parts already sold:

Sideskirts

post-74107-0-86389700-1299734734_thumb.jpg

post-74107-0-11080000-1299734749_thumb.jpg

post-74107-0-79997800-1299734764_thumb.jpg

post-74107-0-45002400-1299734773_thumb.jpg

post-74107-0-67917100-1299734785_thumb.jpg

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

What condition Is the center console lid an price

Cheers

Its in good nick, no marks, $30. Thanks

Heres a pic of the seats as requested. Thanks

post-74107-0-10359100-1299829864_thumb.jpg

post-74107-0-82549700-1299829875_thumb.jpg

Edited by griffonfamily

What condition is the steering wheel in and how much?

Also price on cigarette lighter?

Steering wheel in reasonable condition, just started to craze in a few spots, better than most I have seen. $80 with airbag. Cigarette lighter is sold.

After those clips holding the brake lines across the firewall of the enginebay. If they are in good condition lemme know how much you want :)

Its a matter of getting them off but all being well, $20 posted. Thanks

Would you have all 4 stock wheels?

One or two have very slight gutter rash, two tyres are near new, the other two are worn more on the inside but still would have at least 50% tread left. Want $150 for the set.

Hey Mate, I was after the 2 x plastic sail pieces behind the side mirrors ? (Triangle type of shape) also the clear plastic piece on the interior light (The front dual one)

Postage to NSW.

Thanks

Paul.

Hey Mate, I was after the 2 x plastic sail pieces behind the side mirrors ? (Triangle type of shape) also the clear plastic piece on the interior light (The front dual one)

The plastic sails have had tweeters screwed to it but you can grab them if you want them for $10. And the clear plastic piece on the interior light for $20 posted. Or together $25 posted. Thanks

Postage to NSW.

Thanks

Paul.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...