Jump to content
SAU Community

Recommended Posts

Hello Fellow Skyliners...

Just purchased a 96 Silver, series 2, r33 with larger exhaust and 18 inch rims about the only mods. The car is auto - not what I originally wanted, although when driven - still amazing fun.

I do have a question for the more experienced campaigners...

After nearly red-lining in 1st - 2nd - a swirl of grey/white smoke (not always) is expelled from the exhaust - usually happens when I lift off the gas... I am assuming that this is a whole load of fuel being dumped - but wanted to confirm. Is my car a 747 dumping fuel on the ocean before landing? Or was my car born to me with a slight handicap of sorts?

Link to comment
https://www.sau.com.au/forums/topic/35779-new-owner-white-smoke/
Share on other sites

if it was fuel it would be black smoke.

Isnt white smoke from water? Does this happen when you first drive your car or even after its been driven for say 1 hour?

It usually happens on cold mornings as condensation in the exhaust system gets evaporated.

Ok - def white smoke - not usually after rain... Although, after car warms up and shoots a couple of loads - no longer really evident.

Thanks for advice, will def check out with the boys at Garage. Just having too much fun to worry about it at the mo :D

Did reset the ECU the other day - fuel consumption has dropped and less of the smoke'n...

Condensation??? Hmm - the exhaust is rather large? :D

Cheers.

i hope its not turbo seals , take it to a long downhill engage low gear say 3rd so its fairly high rpm 5-6000 stay off the gas pedal when you get to the bottom of the hill then push the gas pedal and watch in the mirror if you get a cloud of smoke either blue of grey whitish its not good . depending on the colour ( grey , white turbo seals ) blue =rings and or valve seals .

ps make sure engine is normal temp not cold , any black smoke is unburned fuel .

Don't want to be too negative Alex but i don't like the sounds of it. Get a leakage or compression test done as soon as possible incase it's doing some damage. I had the same problem with my R33, blowing a big cloud of white smoke when i eased off the gas after giving it some stick. Initially thought it was a blown turbo, then found out ringlands in one cylinder were f*cked. Hello $$$$.

Worked out that there was a lot of blowby in one cylider causing the cloud, but as the pistons heat up and expand, the problem doesn't seem so evident. Full rebuild in the process for me. Hopefully get the car back this week.

Hopefully for your sake it's not so bad.

Good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
    • Any idea where I can get genuine MAF apart from used ones? I can't find any only for GTRs and unfortunately that price is not in my budget 🤣 I might gap my plugs down and put my splitfires in, they were only in for a year or so before I started the rebuild 
×
×
  • Create New...