Jump to content
SAU Community

Recommended Posts

Hi,

The R30 has been sitting in the yard for two weeks. Usually it starts first time, even after many weeks, however now it fires for a second or two and then dies. After that nothing, the engine just turns over.

If I wait a minute, switch ignition off and then try again, it does the same thing, fires for a second then dies.

I can hear the fuel pump priming. There's fuel in the tank and the fuel filter is full of fuel so the fuel pump is working. There must be some spark because it does fire briefly. Coil is new, and the new coil gives same symptoms as the old coil. No obvious leaks anywhere, battery is fully charged. I recently replaced the temperature sensor and cold start valve (with parts from wreckers) and car was running well when last used.

Any thoughts on what to check next?

JH

Link to comment
https://www.sau.com.au/forums/topic/358885-r30-wont-start/
Share on other sites

Id also check if the injectors have leaked and then gummed up (fuel tyurned to varnish like substace) and now blocked.

Same thing happened to me!

It would run for a few seconds then just die.

I found out the cold start injector (the agricultural irrigation like fuel injector in the intake plenum) was spraying enough fuel during cranking to actually get it to run. Once the starter motor stops the cold start injector stops too.

Maybe test it out by un-plugging the cold start injector (simple clip on plug) and see what happens.

Link to comment
https://www.sau.com.au/forums/topic/358885-r30-wont-start/#findComment-5735215
Share on other sites

Thanks Andrew,

I'll unclip the cold start injector and test your theory. Is it likely that all the injectors would gum up? Maybe the relay is faulty.

@Peter, I think the dizzy/ignitor is OK. It's the 'newest' component on the car.

Link to comment
https://www.sau.com.au/forums/topic/358885-r30-wont-start/#findComment-5735290
Share on other sites

Thanks Andrew,

I'll unclip the cold start injector and test your theory. Is it likely that all the injectors would gum up? Maybe the relay is faulty.

@Peter, I think the dizzy/ignitor is OK. It's the 'newest' component on the car.

[/quote

I have just been thru this.

Get some throttle body cleaner. Clean the AFM and the throttle body. Worked for me. 100%

Link to comment
https://www.sau.com.au/forums/topic/358885-r30-wont-start/#findComment-5735859
Share on other sites

...

I have just been thru this.

Get some throttle body cleaner. Clean the AFM and the throttle body. Worked for me. 100%

That did the trick (plus a new fuel filter). Back on the road.

Thanks for all the replies.

JH

Link to comment
https://www.sau.com.au/forums/topic/358885-r30-wont-start/#findComment-5739298
Share on other sites

Hi Socrates,

I suspect the fuel filter was the main problem. The throttle body was very dirty so cleaning that must have helped. As for the AFM, it was reasonably clean but I also cleaned up the electrical plug and connectors.

The problem with EFI is that a fault in any one of the sensors, relays, connectors (or an air leak!) can cause problems or stop the engine from running. I collected a set of relays off a wreck today - just in case (!). I probably need more testing tools, a fuel pressure gauge would be useful - for a while I thought that the fuel pump wasn't delivering enough fuel.

JH

Link to comment
https://www.sau.com.au/forums/topic/358885-r30-wont-start/#findComment-5739405
Share on other sites

I can confirm that there has been alot of problems with fuel since the floods in qld. I know of at least 6 cars now that have crapped themselves due to fuel. Tank clean and new filter, and purged lines have fixed them all.! (including my R30 Hatch which is in Brissy at the moment)

Link to comment
https://www.sau.com.au/forums/topic/358885-r30-wont-start/#findComment-5740330
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean it's a bit late to say "This won't have any tangible effect and it is not worth spending more than about three seconds on it, please just enjoy the car" But I said it anyway. Does the pod actually get any airflow in that position behind a bumper like that?
    • Hey guys - apologies for digging this up. Has this website been shutdown or is the outage temporary?
    • So, went shopping at Just Jap for things that might work for the intake  After some trial fitting there I ended up with a 3" x 45° silicone bend, a 3" x 300mm alloy straight, and a humped joiner, some minor trimming will be required to shorten some of the stuff, but nothing that is beyond my "ham fisted" skills The guy at Just Jap was most helpful as we had all sorts of joiners,  bends and stuff out trial fitting  Laying it out above the stuff in there it seems everything will fit nicely, and looking at it, it is probably the way I should have been looking at doing it from the beginning, probably..... In the end it is a front bar off job anyway to remove the original stuff behind the front bar that is taking up the required realestate needed, so maybe a Thursday or Friday job And because I'm a hopeless consumer, I grabbed some new steel wheel nuts, the current ones are a spline drive type with a "security" socket, that somehow someone keeps misplacing, the new ones are a basic black steel 17mm hex socket In other news: I just did my "final" tax return, I am now officially a old retired veteran pensioner, and I'm milking the system for all it's worth,  life is good
    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
×
×
  • Create New...