Jump to content
SAU Community

Recommended Posts

Check your cooling system, Clint.

Only a matter of time before you blow a gasket or something.

Oil temps shouldn't be high with just regular driving even with the ambient temps we're getting.

The old 180 sat perfectly fine in 40degree heat not moving with the aircon on...until she started overheating after a thrash and then the Koyo went in :P

Rad flush and fresh coolant + thermostat will get her all nice and purty again ;)

Ah that's good...yeh the oil does creep up a bit on these hot days man :/

Oh nice! That must've been one of the two resident 35's we have here. Man imagine driving that thing around all day knowing you got so much f**king power :O

Thanks guys. Coolant temp never moved, was just oil temp got higher than normal.

Saw a gun metal/dark purple 35 pulling onto Margaret on Boxing day. Was totally jello

I don't know how accurate the R34 gauge is for oil. It could be out of whack.

However, if it is correct, then elevated oil temps can be linked with the inability of your cooling system to keep temps in check.

The nissan water temp gauge is the most inaccurate thing ever. Once it indicates things are hot, you've cooked the motor :yes:

I was lucky enough to catch my gauge in the process of getting hot...it was only 3/4 of the way but by then, even my intercooler cold pipe too hot to touch. Managed to crawl the old girl home with the heater on full whack to help with temps.

New coolant and thermostat (optional) is cheap. Cheaper still that there are mates out there willing to help.

1 weekend without alcohol is all it costs LOLOL :ph34r:

Ah that's good...yeh the oil does creep up a bit on these hot days man :/

Oh nice! That must've been one of the two resident 35's we have here. Man imagine driving that thing around all day knowing you got so much f**king power :O

I'll be owning one of these after this weekend HA ;)

Moving into our new place at Laidley on thursday, guess I'd better start trolling this thread more. Hopefully I can get the 32 fixed and come on some cruises soon. Stupid ceramic turbos.

Sounds good bro, I'm in the next town over at Gatton. if someone waves at you from a Red and Black 33 that'd be me :)

Finally moved in and internet connected, getting car moved out here next week so I can start ripping it apart ready to replace dead bits. If I see an orange and black 33 I'll be yelling 'abomination' and pointing.

Finally moved in and internet connected, getting car moved out here next week so I can start ripping it apart ready to replace dead bits. If I see an orange and black 33 I'll be yelling 'abomination' and pointing.

You have just become...

One of us. :D

Now sign up as a member :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...