Jump to content
SAU Community

Shift Light Help

NSM033

By NSM033,
in Engines & Forced Induction

 Share

Recommended Posts

NSM033 Enthusiast

NSM033

Posted
Posted

i've got an auto meter shift light that hooks up to the coil, power and earth. as there are 6 coils on the rb25 how do i hook it up? do i conect it through the loom at the back to all 6 or do i just need to conect it to one of them, if so which one? any help would be much appreciated. thanks

Link to comment
https://www.sau.com.au/forums/topic/366040-shift-light-help/
Share on other sites
WYTSKY Veteran

WYTSKY

Posted
Posted

I have a tacho with a shift light and that has power,earth,illumination (when ur lights go on) and signal, that u just tee off from ur loom, I think it is yellow with a green stripe, or green with a yellow strip, something like that.... you dont hook it up to your coils

Addicted2BoostR34 Proficient

Addicted2BoostR34

Posted
Posted

253990_226367924055773_100000477008080_959234_3201748_n.jpg this is the wire i have hooked my digital tacho up too on my 25.. it should be a medium size green one (( not sure about colour been a while since i done it ))

i just used one of them splices where u lay the two wires next to each other and push the steel pins down never missed a beat

make sure i lay the ecu plug out and get the right wire !!!

(((@@ you do this at ur own risk if u make a mistake dont came back on me mate @@))

:cheers: :cheers: hope it helps tho i would take a pic of mine but its at the machanic for the next 2weeks :cheers: :cheers:

i've got an auto meter shift light that hooks up to the coil, power and earth. as there are 6 coils on the rb25 how do i hook it up? do i conect it through the loom at the back to all 6 or do i just need to conect it to one of them, if so which one? any help would be much appreciated. thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Roy
      Ben's R32 Gtst Build

      By Roy · Posted

      Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • GTSBoy
      Another little story of weird shit happening

      By GTSBoy · Posted

      Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • MBS206
      Another little story of weird shit happening

      By MBS206 · Posted

      Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Shizu
      Returning after a long time!

      By Shizu · Posted

      Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • dbm7
      Looking for a part number for this part here

      By dbm7 · Posted

      Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...