Jump to content
SAU Community

Recommended Posts

Hey guys in a bit of a pickle!

Was driving the other day and car just cut out on me and wouldnt start. I then looked under the hood and saw that i melted my o2 senssor wires onto the turbo manifold and that appeared to be the problem until i disconected it and tried starting with no o2 seonsor and got nothing. Next i took off the fuel lines into the engine and turned ignition on and found no petrol pumping or any sort of prime noise! So i took the fuel pump out and stuck it directly into the engine and ran it manually and the car started and reved up. So i assumed i had stuffed one of my relays to the fuel pump. To my understanding it is either both or one of the one behind the ecu in pass kick panel and in boot to the right of fuel pump fuse. They appeared to work fine after testing. Next i tried looking at the pump control unit and found no burns on the board but am not sure if there would be from 12 v? So not sure if thats working or not. Also i ear there is a ballist resistor connectin to the fuel pump in the boot which i have not yet looked at but am not sure what its duty is and if it can actually short circuit?

Need help! :)

Oh and also tried a mates ecu and nothing. So inconclusion there is no power on the wires on top of the fuel lid

To test if it has power you need to be holding the test light on the wire then get someone turn on the igntion and it should have power for a few sec. If that doesnt work take the next step and starting testing the power wire on the relay and also the triger wire on the relay and if thats all fine you should check if the relay is clcking.

  • 1 year later...

Its a pretty old post, but i did the same thing a while back on mine. Melted the 02 on the dump pipe.

It blew a fuse obviously and killed the whole car (travelling @ 100km/h down the freeway).

Changed the fuse and all was well. But over the next year, things started crapping out. I have a feeling the short melted something somewhere, and things werent getting adequate current. 1st the fuel pump (re wired onto the 4WS 12v), then my boost controller (re-wired off the AFM 12v.. using MAP so it was spare) and now, my Idle control isnt getting enough current. I am assuming all these things were feeding off the same circuit.

I asked about backfeeding the circuit, but it wasnt adviseable lol. So just took feeds from elsewhere.

So before going and ripping out the fuel pump, just throw a multimeter over it. I found that unless my walbro had EXACTLY 12v, it would not kick into life. The feed was only supplying a fraction over 11v. Same with the boost controller. Never knew they were that picky. heh

Edited by gotRICE?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...