Jump to content
SAU Community

Recommended Posts

Hey all,

Well its time to finally part with my kawa. Its been a good bike but time for loan repayments followed by an upgrade. i bought it off a mate of mine cause of its condition once he was out of his rescrictions and i was on them.

Its a 2001 kawazaki zx6r.

If your mates got a cbr250 and thinks his fully sick... this is a completely different level.

ALWAYS GARAGED!

unfortuanly i dropped it at around 10ish kms an hour causing cosmetic damage. I HAVE SINCE REPLACED ALL FAIRINGS and is back to looking great. Photo is how it looks now! Does have a scratch here and there on exhaust etc.

I dont want this thread to turn into a discussion on how a zx6r could never be LAMS approved... fact is its had ownership between the original owner to my mate then him to me and in that time many rego stickers changed and it continues to stay LAMS approved. If you want to talk anymore about that pm me.

Comes with a muzzy echaust system.

5K without roadworthy

5.5k with it. - No idea what it needs for roadworthy if anything. Just sorta cbf.

pm me/ sms me/call me 0433581520

only got 1 pic on my computer

IMG_0184.jpg

Link to comment
https://www.sau.com.au/forums/topic/370775-redbull-zx6r-5k/
Share on other sites

Had a look, Just the one compliance plate so I guess it's aus delivered.

I would have been quite surprised if it was an import

Had some interest from people in other states, but she's Still for sale, someone come buy this thing, it's beautiful!

Link to comment
https://www.sau.com.au/forums/topic/370775-redbull-zx6r-5k/#findComment-5915786
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...