Jump to content
SAU Community

Recommended Posts

Hey guys, just wondering can you wax your car straight away after polishing? or is there a time period you have to wait after polishing?

In short, yes you can.

In long, I like to polish then us an IPA 50/50mix with water wipe down to get rid of any residue, then follow up with a synthetic sealant topped with a wax for that extra depth.

Regards,

Mitch

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5925250
Share on other sites

Yes you can, just don't wax then polish. Although if you dont polish you wont remove any swirls or fine scratches you may have on the surface.

Correct,

I would suggest you give your car a wash, claybar, and wash again then apply a decent wax.

You only need to clay bar 6 monthly at worst but most likely yearly.

These are what I would use on a budget.

Clay Bar Kit

Wax

Wash Shampoo

Regards,

Mitch

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5926300
Share on other sites

Clay bar does wonders. After a polish the water just beads. It makes me laugh when it rains and the 33 is the only car beading 99% the time. Theres alot of lazy kunts that dont clean their cars :P

LOL! I just spent 5 hours on my 33! haha i didn't use a clay bar I used paint cleaner instead.. and mannnn does it look good.. The rain just rolled right off it today :P

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5929676
Share on other sites

Clay bar does wonders. After a polish the water just beads. It makes me laugh when it rains and the 33 is the only car beading 99% the time. Theres alot of lazy kunts that dont clean their cars :P

Hi,

Is it necessary to dry the car then use the clay bar? Or would it be o.k to just spray the lubricant while the car was wet and use the clay bar?

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5931711
Share on other sites

Clay bar does wonders. After a polish the water just beads. It makes me laugh when it rains and the 33 is the only car beading 99% the time. Theres alot of lazy kunts that dont clean their cars :P

Do you mean you clay bar after a polish?

LOL! I just spent 5 hours on my 33! haha i didn't use a clay bar I used paint cleaner instead.. and mannnn does it look good.. The rain just rolled right off it today :P

Paint cleanser and a clay bar are VERY different a clay bar will remove all the iron particles, industrial fall out, and other contaminants where as a paint cleanser wont.

A paint cleanser will help prepare the paint for a wax or sealant helping remove oils that will hinder the wax or sealant from adhering.

Just as an FYI.

Ps check out my site the 1964 Cadillac had approx 25 hours machine polishing alone not including any thing else! www.immaculatereflections.com.au

Regards,

Mitch

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5931762
Share on other sites

apologies for hijacking thread, but just wondering if using a clay bar will help get swirl marks out?

gave it a polish/wax over the weekend & it helped, but still got some damn swirl marks on the bonnet haha

cheers guys !

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5933316
Share on other sites

apologies for hijacking thread, but just wondering if using a clay bar will help get swirl marks out?

gave it a polish/wax over the weekend & it helped, but still got some damn swirl marks on the bonnet haha

cheers guys !

A clay bar removes contaminants and industrial fall out from your paint, it wont remove marks or scratches. Polishing is what removes that.

My other thread may help you http://www.skylinesaustralia.com/forums/topic/369354-detailing-and-car-care-de-coded/

Regards,

Mitch

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5933414
Share on other sites

The clay bar also requires constant kneading so that the pollutants and particulate matter don't stay between the clay bar and paint...

> otherwise more scratches can be generated.

> whilst it's necessary, a lubricant can't do it all.

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5934791
Share on other sites

The clay bar also requires constant kneading so that the pollutants and particulate matter don't stay between the clay bar and paint...

> otherwise more scratches can be generated.

> whilst it's necessary, a lubricant can't do it all.

I would say folding as opposed to kneading just so it doesnt confuse people. You want to fold it over so the part you were previously using is now in the middle of your "pancake shape" clay.

Link to comment
https://www.sau.com.au/forums/topic/371652-polish-then-wax/#findComment-5934830
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers)
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
×
×
  • Create New...