Jump to content
SAU Community

Recommended Posts

hi guys,

here i have my 1994 R33 GTST for sale $18,500 ono make me an offer i cant refuse . it has just had a new custome pearl maroon paint job, and recently rebuilt and forged by EFI on the gold coast. i need to sell this due to the fact my fiance and i are moving to melbourne in 2 months now and dont want to take it down there.. this car is for serious buyers as it is very quick powerful and dangerous to the inexperienced driver.

it is still registered and can supply road worthy if needed. the car just has a 1000km done on the new motor as its just run in after the new build . dyno sheet can also be supplied, here are some of the following done

Engine mods:

plazmaman plenum

plazmaman throttle bodie

alloy radiator

ARP rod bolts

ARP head studs

ARP main studs

ACL bearings all round

CP pistons

H beam rods

tomei cams

new valves and springs

new valve seats

head port and polished

block honed

balanced and linished RB25 crank

new hoses

new alternator

new powersteering

splitfire coilpacks

brand new GT30/82R garret supplied by MTQ brisbane

link computer

custom painted engine covers and timing cover (not in picture)

custom catch can with speed flow fittings, done by EFI also (not in picture)

interior:

autometer gauges and tacho

APEXI AVCR boost controller

HKS turbo timer

mongoose M80G alarm

sparco gear knob and boot

momo race steering wheel

cutom carbon fibre dash

Bodywork:

Do-luck front bar

custom side skirts have just been done(not in picture)

brand new custom skyline maroon paint job with pearl

so guy's make me an offer and i will consider it

. please feel free to pm me or text 0458924408, thanks sam and katrina

post-80542-0-32462000-1311878008_thumb.jpg

post-80542-0-85676100-1311878014_thumb.jpg

post-80542-0-17558800-1311878021_thumb.jpg

post-80542-0-02602600-1311878030_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/372386-r33-rebuilt-forged-rb25/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...