Jump to content
SAU Community

Recommended Posts

It would cost you so much your head would explode.

The box my kit came in was so big it didn't fit in a Mitsubishi Triton. It fit in a single cab falcon but with a fair bit hanging out the back.

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Yeh im just getting side skirts tho so i wont need a massive box for the front and rear bars, i had my exhaust sent via USPS and it cost around $300 in total and that was really heavy, im thinking it would cost around 150-200 to USPS a set of side skirts over.

  • 2 months later...

G'day Sheldon - Nice write up.

Looking and doing an uprev tune myself. i have contacted tokyo motorsports in Perth (Im from near melb) and they asked me to send over my ECU for an uprev "etune" - derstricting & throttle mapping tune.

Does that sound right?

BTW - aside of power - do you have some crisper response and a bit more above th 5000rpm zone?

I didn't have to send my ECU over, the guy i was dealing with just sent me a beggining map and i worked from there.

I found it 10x easier to spend the extra $250 and buy the tuners pack personally, then take it to a local tuner with a dyno and do test runs there.

eTune will never get you the same kind of tune as a tuning shop with a dyno.

5000+ is very responsive, definitely kicks you back around that marker.

Thanks For that - Starting to think the same about dyno operators.

Only problem of course is finding one in melbourne or sydeny!

Lookig at this stage that I might be making a trip up there to get it done.

Thanks for your help - also good to see another 70th owner.

Cheers

I didn't have to send my ECU over, the guy i was dealing with just sent me a beggining map and i worked from there.

I found it 10x easier to spend the extra $250 and buy the tuners pack personally, then take it to a local tuner with a dyno and do test runs there.

eTune will never get you the same kind of tune as a tuning shop with a dyno.

5000+ is very responsive, definitely kicks you back around that marker.

  • 1 year later...

Nice. I have done all the mods as above minus the Exhaust (Only installed the ART Pipes for now).

Question about the Double Din and player.

I had this installed for me by an automotive audio/electrical professional. Everything works fine on the display but i cant get the original (Trip metre/leaf Display that pops up) to display anything

I did get a cheap $350 display unit that came with the lot... gps , reverse camera , dvd etc.

Did you use an adapter?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...