Jump to content
SAU Community

Watanabe Rs8 17X8 17X9 With Re-01R

masTers
 Share

Recommended Posts

masTers Mentor

masTers

Posted
Posted

Classic RS8 wheel but in 17 inch instead of the standard 16s.

17x8 + 35 with 235/45 Bridgestone RE-01R with a fair amount of tread left

17x9 + 40 with 255/40 Bridgestone RE-01R with not a great amount of life left

Offsets should be fine for an R32-R34. They clear 4 pots no worries, but I'm not sure about brembos. Rears have a baby amount of dish (approx 1 inch)

The 17 inch RS8 retails for 63,000yen as a special order from Watanabe.

Gold centres, no gutter rash what so ever. Have centre caps but no nuts.

$1200. Located in Yokine, Western Australia.

Happy to send anywhere in Australia if buyer organizes postage (Will be happy to deliver to any courier depot as well)

th_IMG00003-20101014-1250.jpgth_IMG00005-20101014-1250.jpgth_IMG00001-20101014-1249.jpg

Link to comment
https://www.sau.com.au/forums/topic/373910-watanabe-rs8-17x8-17x9-with-re-01r/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Predator1
      Tomei gasket

      By Predator1 · Posted

      Didnt realise RB's had more then 1 head.
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • Kinkstaah
      Unpeeling the Orange

      By Kinkstaah · Posted

      The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...