Jump to content
SAU Community

Recommended Posts

Car is listed on carsales.com.au for $25k. For SAU people $22k firm and please mention you saw it on SAU =)

Email : [email protected]

Phone: 0468 327 274

Location: VIC, Glenroy

My last car was sold here, an S13, that went to a member in the NT. Happy to send interstate, you'll need to organise pickup from my location.

The following has been done:

- Exhaust from dump pipes back

- 18" rims, powder coated black

- Exedy clutch approx one year ago

- Adjustable cam gears

- Tint on the rear and passenger windows

- Kenwood headunit, Sony 6x9s and Response amp.

- Viper alarm with remote start and other modules

- Slotted front rotors

- New 245x40x18 tyres

- New battery approx 3 months old

I am the first owner in Australia and have owned the car for two years. Only having done minor modifications the car has been dynoed at two workshops both showing 245kW at the wheels.

100 thousand KM service (all fluids, water pump, belts, timing belt etc) done by Racepace. Minor services done by Creatd. Next service due is in 2000 KMs. The car was dynoyed at said workshops.

Compression tests done have with each cylinder basically the same. The injectors have been cleaned and flow tested. Mechanics have commented on a healthy and strong engine. Have been told a PowerFC would see close to 300kW with no other modifications.

It has been regularly serviced and well maintained as this car is my pride and joy. It has never been tracked, never been "at the drags" and is a regretful sale. Most GTRs for sale have a long list of modifications, mine does not. The R33 GTR was my teenage dream car and didn't want to trown a catalogue at it. This car was my weekender and my daily drive for awhile. Bought with 85,000 KM on the clock it has 118xxx genuine KMs on the odometer.

The car is for sale due to plans to move overseas. If I could bring it with me I would, the decision to sell hasn’t come lightly.

As stated I already have the RWC. Would like to sell while the RWC is valid. RWC was obtained 2/9/11. Registration expires 2/5/12, in 8 months. Contact me with any further questions and to organise a time to inspect. It will impress.

BITS YOU'D LIKE TO KNOW

- Drivers side window switch is dicky. If it the window goes all the way down it decides when it wants to come back up. If the window doesn't go all the way down it will go up on command.

- The new rubber was purchased for the RWC. It isn't the stickiest.

- The car hasn't been resprayed so you'll find small scratches, stone chips and the likes. The front splitter needs some love too.

- The AFMs gave me grief for a while. 4 sets (8 AFMs!) later and having them re-wired to the ECU at the 3rd set, this is no longer a problem.

- When tyres are removed from the rim it takes some powdercoat off. This has been done twice, for a tyre puncture repair and the new tyres. Unless you get close you can't see the black enamel paint on some parts of the rim.

Link to comment
https://www.sau.com.au/forums/topic/376225-fs-vic-95-r33-gtr-v-spec-with-rwc/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 2 months later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 months later...
  • 4 weeks later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...