Jump to content
SAU Community

Recommended Posts

hey guys

up for sale are a couple of sets of wheels i have laying around.

#1

19" Locksmice Mesh wheel in chrome. wheels do not have any buckle or dents but 3 out of the 4 do have gutter rash. gutter rash is repairable. would be looking at around $80 a corner to fix. some wheels also have chrome either slightly flaking or slight fade. decent amount of dish also.

Price: $1800

specs:

19X9 +25ish (no stamp so was messured) fronts

19X10+25ish (no stamp so was messured) rears

all four wheels have good tyres. around 80% tread running 245/35/19

only managd to get pics of two wheels. other two wheels are in storage but wheel conditions are the same as pictured.

front:

c70576f6.jpg

dish test :P

b51cebac.jpg

rear

5f33c522.jpg

dish test rear :)

db397b67.jpg

#2

set number 2 are Super Advan Sa3r. rims have no dents or buckles. wheels have very light gutter rash. lips will need to be repainted as the blue is wearing out. the only down side is out of the 4 wheels, 3 are 7" wide and 1 is 8". didnt realise when buying as i wasnt notifted by seller.

Price: $150

specs

3 of the wheels are 16X7 +35

1 of the wheel is 16X8 +38

wheels are sold with no tyres.

2dc2dc58.jpg

ca052ef8.jpg

both sets of wheels are located in SE melbourne.

thanks

Ash

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...