Jump to content
SAU Community

Recommended Posts

ok may be a dumb n00b query but here goes...

when i take my car (95 NA R33) to the redline in 1st gear it starts 'coughing' until i change into 2nd and then at the redline in 2nd till i hit 3rd..

its sort of like a misfire but without the sudden lurching juddering loss of power.

would there be a limiter on the car? or could it be a fuel issue? or could i just be a really crap driver :)

the car is standard apart from an aftermarket exhaust.

Link to comment
https://www.sau.com.au/forums/topic/38008-my-r33-has-a-cold/
Share on other sites

your speedo is getting less accurate as you go faster. Considering 10% accuracy allowance as per ADR rule, a ground speed of 180km/h where your speed limiter kicks in may be shown as 180km/h plus or minus 18km/h... so can be somewhere from 162km/h to 198km/h on your speedo (+/-2cm past ur 180 mark). Speedo also get less accurate as car is older, sometimes by as much as 10k at only 60km/h!

ask a copper to double check your ground speed with his radar, then you'll probably find out for sure :D

Link to comment
https://www.sau.com.au/forums/topic/38008-my-r33-has-a-cold/#findComment-767616
Share on other sites

not all speed limiters limit you to 180klms, in a WRX it's 205 for an auto 210klms for a manual.

So it wouldn't suprise me if you could get up to 220-230klms before it limits the speed, you'll crap your self when it happens the first time.

As it feels like your've just totally f**ked your engine, real bad.

That's also saying you still have the speed limiter or it's turned on.

Link to comment
https://www.sau.com.au/forums/topic/38008-my-r33-has-a-cold/#findComment-768080
Share on other sites

Hey asylum,

It does sound like the rev limiter, mine makes the cold sounding noise (even tho my friend thinks its a sweet noise) when it hits redline. :)

But if you are not sure.. take it to your mechanic and ask him.. I'm sure if he is a good/nice mechanic he wont charge you for this. :rofl: Or alternatively try to drag a car knowledgable friend next time and ask him when it happens again.

Link to comment
https://www.sau.com.au/forums/topic/38008-my-r33-has-a-cold/#findComment-768780
Share on other sites

Hey asylum,

It does sound like the rev limiter, mine makes the cold sounding noise (even tho my friend thinks its a sweet noise) when it hits redline. :)

But if you are not sure.. take it to your mechanic and ask him.. I'm sure if he is a good/nice mechanic he wont charge you for this. :D  Or alternatively try to drag a car knowledgable friend next time and ask him when it happens again.

yeh i like the sound too but i don't wanna kill my engine hehe

cheers guys :rofl:

Link to comment
https://www.sau.com.au/forums/topic/38008-my-r33-has-a-cold/#findComment-768982
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...