Jump to content
SAU Community

Recommended Posts

As a few of us are going up Friday to catch the track day nice n early the next morning, I thought I'd organise a cruise up there for everyone after work

This is not an official SAU-Vic event, just a cruise up as a group.

When: 28th October 2011

Time: Meet 5.30-6pm, departing at 6-6.30pm

Itd take approx 1.5hrs to drive up

Where: Hungry Jacks, Roxburgh Park

Cnr Somerton Rd & Reservoir Drv Roxburgh Park 3064

Link to comment
https://www.sau.com.au/forums/topic/381186-skyline-cruise-to-sau-nationals/
Share on other sites

Hey mate, just letting you know, most of SAU VIC will be going to these premeets:

When: Friday 28th October

South East Premeet:

Where: AMF/AUTOBARN /NANDOS on PRINCES HWY in Clayton.

Time: Meet at 11:30, depart at 12 to arrive in time to Meet point 1

We will take the toll free way through princes hwy to the western freeway.

Meet point 1:

Where: Western Ring Rd Maccas/Mobil (near Boundary Rd exit)

Time: 1pm if you want to have a chat beforehand, get fuel, snacks etc. LEAVING at 2pm.

Meet point 2:

Where: BP Wallan on Hume Fwy outbound

Time: meet at 2.30, as we will most likely be driving through between 3-3.30pm.

Will swing past and grab everyone on the way, so if Wallan is less out of the way for all North/Eastsiders, just meet us there...

One thing is, since its a long weekend, most people leave melbourne at 4-5pm for a holiday, thus a lot of traffic, it wouldn't be a 1.5 hour drive with the traffic. I recommend leaving earlier. Just a suggestion :]

Not stopping you from doing this meet. :]

Thread for meets: http://www.skylinesaustralia.com/forums/topic/380132-friday-cruise-to-import-monster-sau-nationals/

Edited by PENGUYEN
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...