Jump to content
SAU Community

Guages (Defi, Greedy, Pivot, Ect)

fatz
 Share

Recommended Posts

fatz Grand Master

fatz

Posted
Posted

All for sale as I have bought a Haltek and Racepack dash, some of these were in my shed and taking up space as well

First off we have a Defi Link set:

80 mm boost(new) $200

80 mm tacho(used) $200

60 mm oil pressure(used)$250

60 mm oil temp(used)$200

60 mm water temp(used)$200

Defi Link thing number 2(used)$100

Warning meter (new) $50

IMG_0790.jpg

Oil temp and pressure come with mount so you can just bolt it on (fits gtr and rb30)

Water temp comes with a mount to plug straight into a gtr

All sensors and an extra 2m link wire included as well

Condition is all good

Obviously I want to keep it all together and sell as a job lot as that easier so if you want the whole lot pm me and we can work out a deal, otherwise i shall separate them

Next up is a Greddy meter set, all used, off my old Zed

They are all silver in colour

60 mm oil pressure $150

60 mm boost pressure $150

60 mm water temp $150

60 mm oil temp $150

IMG_0787.jpg

IMG_0788.jpg

All sensors and wires included

Once again cheaper if you buy the lot

Next one is a Greddy kit in white, all used

60 mm exhaust temp with new sensor $200 (sensor cost more than that alone)

60 mm boost temp used $150

IMG_0786.jpg

Apexi boost gauge, heckit

60mm 30 bux(currently starts at 0,5bar)

IMG_0785.jpg

But wait there is more(how awesome in 5 years of hoarding!

80 mm pivot boost gauge $50

IMG_0789.jpg

and now for the steak knives...

I have 5 x 60 mm Jetspeed EGT sensors(new)

$50 each.. these things are awesome!

IMG_0784.jpg

and an old school Apexi air flow controller $40

IMG_0791.jpg

All located Lower Blue Mountains, Sydney NSW

Pick up or postage at buyer's expense

Pete

0448468884

Link to comment
https://www.sau.com.au/forums/topic/382898-guages-defi-greedy-pivot-ect/
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
scandyflick Grand Master

scandyflick

Posted
Posted

Keen on the 80mm boost gauge and link. How much shipped to SA 5114?

And just incase I change my mind, how much for the full Greddy set shipped?

fatz Grand Master

fatz

Posted
  • Author
Posted

Keen on the 80mm boost gauge and link. How much shipped to SA 5114?

And just incase I change my mind, how much for the full Greddy set shipped?

Looking to keep the defi set complete, but I can do $520 posted for the silver faced Greddy set of four gauges

:)

scandyflick Grand Master

scandyflick

Posted
Posted

Call it $500 flat and you got a deal... I've been on the 31 club too long, keeping the lowball alive and well. Ha.

Shoot me payment details and I'll swing some cash your way.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...