Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Looks a little high, but that is not how Nissan gauges work. Basically all Nissan temp gauges will warm up to their normal running temperature, and sit there until the fluid actually boils (and you have broken something), and only THEN goes off the richter scale hot. Generally they don't move much inbetween.

But you should put a real temp gauge on every Nissan car imho - espeically one with a 95-100 degree warning light. Boiling cars is the 2nd easiest way to blow an engine (next to not enough oil/low oil pressure).

I put an awesome EL overlay over my cluster, and in the process of fitting it put my temp gauge out of scale - mine now sits between the 3rd and 2nd last lines when at operating temp (and already 1/3 way up when cold at start up). That's why I put in a real temp gauge

bleed the system, might need topping up. at that needle position youre probably looking at around 110-112degrees water temp. not the best, but is still operational.

if it doesnt have air in the system, look for a blockage, or check the status of your thermo fans. does it go back down when youre cruising again? if it doesnt, possibly a water pump issue.

Gosh...I and my mech didnt pickup this overheat issue when we do inspection before buying. Now it becomes annoying....

Do you guys think i should go back to Nissan dealer to have diagnosis checks? Or anyone can recommend any reliable mech in Brissy?

Thanks for you guys help~

or just check the fluid level so that you dont pay someone $180 to top up the radiator......

Did check fluid level is full & top water hose is not too hard to press, fan is only running when a/c is on but even a/c on, the temp is keeping in above middle line...what eles i should check by myself?

Your thermo fan should come on even when the a/c is off, once the car gets hot enough.

I would be checking for air in your system (which I bet is the cause). Or get a mechanic to install a water temp probe and actually check your water temp to see if your stock gauge is lying/broken.

bleed the system, might need topping up. at that needle position youre probably looking at around 110-112degrees water temp. not the best, but is still operational.

if it doesnt have air in the system, look for a blockage, or check the status of your thermo fans. does it go back down when youre cruising again? if it doesnt, possibly a water pump issue.

Just found your question when i was a bit panic, sorry, mate~

I havent flush the coolant yet, but will do soon.

What do you mean by "doesnt have air in the system, look for a blockage" how to check it? I check my fan only runs when a/c on but it doesnt go back to normal temp even with fan (a/c on) on or when i am cruising again.

Water pump issue? What other procedure that i can check whether it is water pum failure? Pls advise, thanks~

Your thermo fan should come on even when the a/c is off, once the car gets hot enough.

I would be checking for air in your system (which I bet is the cause). Or get a mechanic to install a water temp probe and actually check your water temp to see if your stock gauge is lying/broken.

Thanks, Andrew. How can you check air in your system?

Unscrew the little plastic bleed screw in the left hand side at the rear o fthe engine. If you look along the water piping you will see it - it is black plastic and has an X in it to unscrew it with a phillips-head screwdriver.

Hi Mikhail, so have you ever checked by Nissan or any V35 SERVICE SPECIALISTS before? Or you just leave it as it is?

I am leaving mine as is as I am pretty certain its normal. I think I saw a similar thread on here that said the same thing. I had mine serviced and no problems were found. Also my needle is just below the middle, yours is above middle.

If you have access to someone with a datascan tool, get them to check the coolant temperature with it, if it is around 85-90 deg C, then I wouldn't worry about it. Especiallly if it doesn't seem to go up and down when driving hard, or climbing hills

If you have access to someone with a datascan tool, get them to check the coolant temperature with it, if it is around 85-90 deg C, then I wouldn't worry about it. Especiallly if it doesn't seem to go up and down when driving hard, or climbing hills

I wrote a proper bleed procedure somewhere on G35, just search my name.

Also get a radiator cap with temp control gauge on it, you can go check yourself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
×
×
  • Create New...