Jump to content
SAU Community

Recommended Posts

hey guys i have my Enkei Rpf1's forsale unsure of off set they came off my mates soarer im changing to some stockies for now. i work for a transport company that ships around Australia just let me know where you are and i can get it to our depots for you and you can pick up from there cheers pm me or text on 0402948881 heres an old pic on my car when i first got it

all the tyres nearly need to be replaced worn on inside edges a few big scrapes (before i got them) $500ono thanks guys

post-53831-0-30802400-1327998889_thumb.jpg

Edited by TwinTurboSupra+R32 Gtst
Link to comment
https://www.sau.com.au/forums/topic/390047-fs-enkei-rpf1-wheels/
Share on other sites

OK 19x8.5 lol and is the offset sound right j-42?? he's pics like everyone has been waiting for..

Also i have these Anz wheels i had them in my shed aswell 18.8.s i could not see a stamp for offset all tyres unroadworthy selling these for $300 they have a bit of dish i had to put them on my car for now as i have no wheels for my car pm or text for info no big marks on them cheers matt. they dont look to bad on the 32

my car has been sitting in my caport since oct so its real dirty thats why the wheels have cob webs and shit on them.

post-53831-0-48906700-1328335257_thumb.jpg

post-53831-0-75253700-1328335278_thumb.jpg

post-53831-0-28019700-1328335300_thumb.jpg

post-53831-0-44153800-1328335323_thumb.jpg

post-53831-0-10325200-1328335345_thumb.jpg

post-53831-0-49735400-1328335368_thumb.jpg

post-53831-0-74540900-1328335391_thumb.jpg

post-53831-0-45154200-1328335413_thumb.jpg

post-53831-0-76371400-1328335437_thumb.jpg

post-53831-0-31074200-1328335461_thumb.jpg

post-53831-0-65109000-1328335497_thumb.jpg

post-53831-0-07200000-1328335522_thumb.jpg

post-53831-0-71198800-1328335542_thumb.jpg

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...