Jump to content
SAU Community

Gtr Parts (Rb26)

OMGGTR
 Share

Recommended Posts

OMGGTR Mentor

OMGGTR

Posted
Posted

Hi guys since im selling some more stuff im putting my oil pump in here so please disregard that thred! also all standard parts came off my Series 3 R33 GTR.

Selling 4 x R34 GTT standard Rims their spraypainted black and the paint is all chipping off so they look crap but their still in good condition under the paint ( suit powdercoat etc) they have rubber but no tread at all need new rubber dont know a price to ask for so just hit me and the highest offer within a week can take them

4 x 25mm spacers bolt on looking at $180 ish ono

1x Trust High volume oil pump its brand new in the box still has sticky coating (anti rust) comes with crank seal and pump gasket need $1000 firm

1x Standard R33 GTR ecu not sure what their worth hit me with something and i might just take it :)

2x standard R33 GTR camshafts bit shabby $50

2x standard R33 GTR cam gears $50

1x set standard valvesprings + retainers $90

6x R33 GTR standard rods they will come with the pistons as no.1 is rooted and i cbf separating rods are all fine $100

have all 24 lifters some are rooted but some are still ok if you need some let me know and i can give each for $20 (as their $98 new from nissan EACH!!)

1x standard decent GTR waterpump $20 no leaks came off working perfectly

1x Turbosmart dual type boost controller the one with the 2 manual adjustments and in cabin missile switch for high + low boost... ( $100 ) ( you must come remove it urself )

Shoot me pm's most of the prices are not set in stone dont be afraid to offer ( within reason )

Cheers ! some pics of oil pump if you need pics of anything else ask and ill upload within the same day cheers!

Contact 0423755986 George ( after 6 weekdays )

post-53107-0-14966200-1330590359_thumb.jpg

post-53107-0-70707600-1330590364_thumb.jpg

post-53107-0-10914200-1330590403_thumb.jpg

post-53107-0-78284800-1330590417_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/393448-gtr-parts-rb26/
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...