Jump to content
SAU Community

Recommended Posts

Hi mate,

have i missed the price somewhere? I am geniunely interested but need alot of questions answered.

How did the piston crack look/where? is there actual compression readings across the cylinders?

I have just been quoted ~$2000 to exchange a motor across 3 workshops across sydney. Is the quote to fix the

piston only or include removal and install of the motor?

Will one piston just be replaced for $1300. Who will be doing this? will headgasket be reused? choice of bearings?

Can this person your using rebuild this motor to my spec seeing its going to be apart already?. No point pm'ing as

im pretty sure theres plenty of other people asking the same questions.

Cheers

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Very valid questions, and your right its very good for everyone to know.

compression across the rest of the motor is outstanding, 170psi, 170, 168, 170, 170 and then cylinder #6 35psi and 50psi on a wet test. first time i did the tests myself i got in the vicinity of 150 but then i noticed my gauge was a little screwed, so i just had it check properly, and then checked again myself with a new gauge to verify the 170psi readings.

The crack is more of a fracture in piston #6, and the rings which were giving the low reading , The valves and cylinder are fine, not bent or anything.

The cause of the problem was a faulty boost crontroller solenoid ( $30 - $50 ), spiking of the boost i was told led to this.

well yes i mean it works out perfectely for anyone looking to do a rebuild anyway or who has a engine ready for a gtr or something similar...

my quote and intentions were to return the car to its normal state with all the mods still ofcourse.

so anyways... basically pull apart the pistons and replace anything surrounding that is needed e.g rings , im not 100% certain what bearings would be used. im pretty sure i would have sourced some decent looking used parts where i could, reason being it was fine handling the power if it wasn't for the boost controller solenoid. i know people may disagree but sometimes money isnt always available when needed.

A close friend quoted to do this for me if i chose to go down the path myself,

i was going to forge the motor if it didn't sell but with certain issues at the this point, im not going to anymore. im going to sell/swap the way it is.

I hope this helps and havn't missed anything. if you want to talk further PM me ill give you my phone number.

alright fair enough, bad luck with the solenoid mate.

check your inbox i sent you some more details, ive got some parts from my previous r33.

let me know also when your free tomorrow

Bump...

Should be gone shortly, haven't been in hurry lately so i apologise to the guys wanting to come out just been very busy.

Always has been a top car to drive, especially down to canberra once a week for a few months straight. receipts for work and dyno papers to come with, always been looked after. really a shame that a small $30 solenoid caused this. A couple of SAU members have had the car checked also and have told me their quotes are pretty much the same as mine, give or take a few hundred.. probably give more so :)

Just have some common sense, if your going to offer me 10k think about it.. your getting a 12k Gtr ...please save your time and dont have sulk when im an asshole back. :)

losing the company vehicle .....

willing to put a few thousands on top for a swap.

otherwise i got no choice but repair and wait close to a month for it to be done through my mechanic.

Edited by binga85

Update

It's in the Workshop now!

Might be getting fixed if i can get it done quicker than 3-4 weeks. otherwise still selling as is.

Inspections may be a little harder now, however PM and we can sort something out possibly over the weekends as during the week will be very hard now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...