Jump to content
SAU Community

Recommended Posts

Hey people,

I'm doing a turbo upgrade on my R34 GT-T, and before i have put new turbo and stuff on, my mate installed a bosch 044 fuel pump yesterday.

Now as i have never done this before i'm not sure what to expect.

So symptoms that have occurred since the installation ;

i) On the highway in 4th and 5th gear, if i put my foot down there is a delay of about half a second before the car will accelerate.

ii) Even after "priming" the fuel pump (switching to 'on' so the fuel pump builds pressure), it still takes a bit to get started (turns over for a bit then sickly comes to life)

iii) This morning i "primed" it, waited for the fuel pump to stop pumping, then turned over the engine, it kept turning over but wouldn't start, so i tried again straight after and this time, once again, it came to life, but very sickly, it ran rough, felt like a cylinder wasn't firing. i then let it idle at around 2000rpm, and all went back to normal after a few seconds.

Now I'm getting told different things, Some people say it's the fuel pressure reg, and others say it needs to be earthed to the chassis and not use the existing wires. As far as i know, the filter sock reaches the bottom (so my mate says), so i'm not sure what the problem could be.

This is the first time i have touched the fuel line on any car so i'm a bit of a virgin to it.

I'm not sure if this will impact it, but when i was driving to go get the new pump installed, i was cruising along the highway at around 2.5k rpm, and the car hesitated for a second (lost power, but only for a second), engine light came on, then went back to normal and engine light went off.

List of engine/exhaust modifications are:

Superspark coils,

0.8mm gap plugs

3" to 80mm exhaust, no cat (still waiting for one that fits)

Pod filter with standard AFM

and that's about it that i think could effect it.

I have an AEM tru boost, but was only running stock boost when this happened.

Thank you in advance for anyone who can help.

Shaydan

i thought the 044 was an external pump and the 040 was the internal pump? maybe that is part of your problem. or it may have nothing to do with it and it may be fine

if your old pump was dodgy then putting a new pump in may be showing another issue that was previously hidden by a failing fuel pump. this may be something simple like a dirty afm or fouled spark plugs.

The stock Fuel pump was fine,

And yeh you're right about it being external, but you can still use them internally.

The FPR has arrived but not fitted and it's still 50/50, c-red and hyperdrive told me over the phone that i have wasted my money because it's not needed, and others say i need it.

I'm not sure if the FPR is related to the hesitation when in 4th and 5th.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...