Jump to content
SAU Community

Recommended Posts

R33 GTR COIL HARNESS, HKS DLI & HKS R33 GTR DLI HARNESS.

1. HKS DLI w/ Universal Harness

HKS Part No#: 43001-AK001

Perfect Condition, Not a Scratch on the DLI Box, Universal harness previously used.

Less than 1000kms use, one run in.

2. HKS R33 GTR Plug & Play Harness 

HKS Part No#: 4399-SN002

Brand New. 

3. R33 GTR Coil Harness

Nissan Part No#: 24079-24U10

Perfect Condition. 

Pics: We all know what they look like but available on request to genuinely interested persons. 

Asking $850 for the lot. 

Contact via PM

More info:

Obviously comes with harness to suit R33 GTR but can be mated up with the following cars using the universal harness. 

Upto 8 Outputs (Coilpacks).

Skyline - R32 GTR - BNR32

Skyline - R33 GTR - BCNR33

Silvia - PS13 (Red Top)

Silvia - S14 S1

Silvia - S14 S2

Impreza - GC8/GF8 Ver1-2

Impreza - GC8/GF8 Ver3-4

Impreza - GC8/GF8 Ver5-6

Supra JZA80 S1

Supra MKIII - JZA70

Skyline - R32 GTS-t - HCR32

Silvia - S13 (CA18DET)

EVO - CD9A

EVO II - CE9A

EVO III - CE9A

Mark II S2 - JZX100

Starlet - EP82

Starlet - EP91

Mark II S1 - JZX100

Fairlady - Z32

Supra JZA80-S2

Soarer - 2.5GT-T S1 - JZZ30

Soarer - 2.5GT-T S2 - JZZ30

Mark II - JZX90

Aristo - JZS147

Aristo - JZS161

Mark II - JZX81

Legacy - BD5 I

Legacy - BD5 II

Mark II - JZX110

GTO - Z16A

GTO - Z15A

THIS WILL NOT FIT;

Skyline - R33 GTS-t S2 - ECR33

Skyline - R33 GTS-t S1 - ECR33

Skyline - R34 GTR - BNR34

Skyline - R34 GTT - ER34

Stagea - 25t RS (~98+) - WGC34

Stagea - 25t RS Four (~98+) - WGNC34

Stagea - 25t RS Four (pre 98) - WGNC34

Stagea - 260RS - WGNC34

From what I can tell they are not made anymore (Well they are discontinued from Nengun) 

Here is a little description:

"The Twin Power ignition amplifier incorporates both the CDI and transistor method ignition to provide optimum spark duration and maximum voltage output, resulting in crisper throttle response and a smoother engine powerband. The CDI method, capacity discharge ignition, provides maximum voltage by transferring all stored energy in the capacitor to the ignition coil so that the ignition current can buildup quickly, thus making the Twin Power very effective in the higher revs where a normal spark would tend to diminish. This strong rapid spark prevents the high rpm ignition miss that reduces peak power. The transistorized method generates high voltage by using transistors to cut off current to the coil, thus allowing for a long energy discharge. This longer spark duration allows the Twin Power to improve lower RPM throttle response and torque. The combination of the CDI and the transistor method incorporates two distinct systems into one high performance unit, hence the designation of Twin Power. The Twin Power produces a spark output that is typically 1.5-2.5 stronger than of the stock ignition system and consumes about 35% less power input than other ignition amplifiers. 

The compact and attractive Twin power unit is constructed of durable anodized aluminum and sealed to prevent moisture corrosion. Universal wiring harnesses are included to aid in installation and mounting. Vehicle Specific wiring harnesses are also available for certain models for easier installation and to support installations that require complex integration.

Dimensions - All Twin Power Units, (except for DLI II), are 91mm (L) x 80mm(W) x 34.5mm (H) and weighs approximately 430g (~15.2oz)

Note: HKS Twin Power Units are not compatible with Non-Resistor Spark Plugs

Combination of transistor ignition type, which improves ignition at low rpm and CDI ignition, which improves ignition at high rpm increase ignition energy itself.

Latest vehicles even normal aspirated engines require spark plugs with higher heat range when intake and exhaust parts are upgraded. Twin Power enables strong spark to start engine and idling will be stable.

Cheers. 

Edited by krayzie32

All 3 items are SOLD thanks guys.

Wont be responding to anymore PM's regarding this item.

Edited by krayzie32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...