Jump to content
SAU Community

Recommended Posts

Im after a highly modified motor

Looking at something With top mount aftermarket turbo, externally gated, cams, injectors, coil packs, and if internals are done it would be a bonus

If you know anyone selling a half cut, crate motor or just got one laying around hit me up

Cheers

Link to comment
https://www.sau.com.au/forums/topic/401661-rb25det-neo/
Share on other sites

How about this on ebay atm...

http://www.ebay.com.au/itm/380442561720

Nissan Skyline R32 2.7L RB25DET Engine GReddy T67 Turbo Manifold Nismo J021

Removed from a full running competition vehicle in Japan!

Engine has been compression tested and produced a perfect 165psi accross all 6 cylinders.

Extremely expensive build, comes as pictured with all piping ready to bolt straight in!

Base RB25DET Engine

RB26DETT Genuine Crankshaft

RB26DETT Genuine Conrods

87mm N1 Pistons

Metal Head Gasket

Cylinder Head Port and Machining

Tomei Camshafts 256/256

HKS Adjustable Cam Pulley Gears

Power Enterprise Timing Belt

N1 Water Pump

Low Temp Thermostat

GReddy T67 25g 10cm Exhaust Housing Turbo

GReddy Stainless Steel Exhaust Manifold

GReddy External Wastegate + Screamer Pipe

Full Turbo to Cat Dump Pipe

GReddy Alloy Inlet Manifold

Infiniti Throttle Body

Adjustable Fuel Pressue Regulator

Nismo 555c Injectors

Z32 Air Flow Meter

GReddy Front Mount Intercooler + Piping

Blow Off Valve

R33 RB25DET ECU + GReddy E-Manage

JUN Oil Cap

R32 Crossmember Modified + Spot Welded

Parts26052012203.jpg

Parts26052012204.jpg

Parts26052012207.jpg

Parts26052012216.jpg

Link to comment
https://www.sau.com.au/forums/topic/401661-rb25det-neo/#findComment-6384919
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...