Jump to content
SAU Community

Recommended Posts

All parts located in Wollongong NSW, can post items :)

EXEDY Single Ceramic clutch (done less than 3,000kms) suits r33 gtst rb25det w/ machined oem flywheel, will handle 300rwkw! - $400

post-60012-0-79507000-1343312114_thumb.jpg

post-60012-0-39354300-1343312123_thumb.jpg

post-60012-0-05236700-1343312153_thumb.jpg

post-60012-0-82504200-1343312166_thumb.jpg

post-60012-0-81220900-1343312140_thumb.jpg

SARD sidefeed 550cc injectors in standard fuel rail (less than 3,000kms old) - $400

post-60012-0-30412700-1343312265_thumb.jpg

Bosch 040 intank pump already in cradle and wired to suit r33 gtst (less than 3,000kms old) - $120

post-60012-0-81666300-1343312278_thumb.jpg

Whiteline KCA347 camber bushes installed in rear control arms - $100

post-60012-0-59906900-1343312463_thumb.jpg

R33 GTST standard exhaust manifold - $30

post-60012-0-65276100-1343312477_thumb.jpg

R33 GTST standard fuel tank - $40

post-60012-0-41386500-1343312487_thumb.jpg

Brand New Rear HICAS balljoints 55154 OP800 -$50

post-60012-0-17281800-1343312636_thumb.jpg

RHS R33 KR4 front guard - $70

post-60012-0-31632200-1343312652_thumb.jpg

Both door trims R33 series 2 - $50 each

post-60012-0-75229000-1343312670_thumb.jpgpost-60012-0-26952900-1343312689_thumb.jpg

R33 dash w/ blown airbag - $40

post-60012-0-89367100-1343312173_thumb.jpg

R33 GTST rear "skyline" garnish - $20

post-60012-0-39079400-1343313161_thumb.jpg

Edited by Luke_GTS-T

SOLD

EXEDY Single Ceramic clutch (done less than 3,000kms) suits r33 gtst rb25det w/ machined oem flywheel, will handle 300rwkw! - $400

SARD sidefeed 550cc injectors in standard fuel rail (less than 3,000kms old) - $400

Bosch 040 intank pump already in cradle and wired to suit r33 gtst (less than 3,000kms old) - $120

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...