Jump to content
SAU Community

Recommended Posts

Hey, i also have a v35 350 gt-8 and can highly recommend southern hi-tech dyno tune in melrose park off south road. They were excellent with the work that I needed done to the car. They didn't bulk at the fact that it had a cvt and their rates are incredibly reasonable. Their details are listed in the SA section. If you have a look in the SA section there is a list for contacts for almost all of the things that you are after.

Hey, i also have a v35 350 gt-8 and can highly recommend southern hi-tech dyno tune in melrose park off south road. They were excellent with the work that I needed done to the car. They didn't bulk at the fact that it had a cvt and their rates are incredibly reasonable. Their details are listed in the SA section. If you have a look in the SA section there is a list for contacts for almost all of the things that you are after.

Cheers mate ill check them out!

Okay, so as for the second key i went to main north nissan and they did me up a quote for an exact replica of my key. Apparently it costs about $450 for a new key and then $90 for a cut and code.. I am going to call up and see if i get a key from ebay whether or not they can cut and code it so i'll let use know.

I got a key cut at North East Lockmiths at Windsor Gardens - $120 for the key, cutting & cloning the imobiliser chip. No remote buttons, but it opens the door & starts the car, so if I lose my other key I'm not stuffed. Just need to turn up with the car & a working key - took around 30 minutes. If Tony's key works I'll get one of those as well, but it will have to have the immobiliser coded at Nissan.

Hey guys just another question, I need a jack for my v35 and I asked nisswreck but they wanna charge me $95 for one they just pulled out of a wreck, which is kinda steep I reckon. I have one from my old R34 but its a little rusted because it was left outside after I rode off the car. My mate was saying you can get a jack from super cheap at will fit it fine for about $50? Suggestions? I could just get the one from nisswreck but if i can save a bit it would be better

Hey guys just another question, I need a jack for my v35 and I asked nisswreck but they wanna charge me $95 for one they just pulled out of a wreck, which is kinda steep I reckon. I have one from my old R34 but its a little rusted because it was left outside after I rode off the car. My mate was saying you can get a jack from super cheap at will fit it fine for about $50? Suggestions? I could just get the one from nisswreck but if i can save a bit it would be better

I picked up a 1200kg jack and 4 chassis stands from Autobarn about a month ago for like $90 for the lot. Jack works perfectly piss easy to setup and use.

  • 1 month later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
×
×
  • Create New...