Jump to content
SAU Community

Alcon Brake Package To Suit Nissan

Risking
 Share

Recommended Posts

Risking Grand Master

Risking

Posted
Posted

I put this setup together for a customer who we have now upgraded to supercar callipers and a pedal box.

These are Alcon 6piston callipers (mono block construction) which are new. They have been fitvehicles vehicle during the build process and have been used to drive in and out of the workshop on one of my supercars for the last

week. They have seen no other work & are in perfect condition.

Come with ferodo pads

Rotors are 378mm 2 peice rotors with black anodized hats. They are a fixed design NOT floating. Rotors have 5x114.3 PCD drilled and a 5x120PCD. Center bore is to suit a skyline.

Machined billet adapters to suit the skyline. GTR required some minor mods to the upright to fit such a large calliper, currently have the smaller r32/33 sized bolts but I can drill them out to suit r34 larger bolts.

No brake lines but they use an m10x1.0thread so most aftermarket braid line kits from the GTR will fit.

I want $3000 for the setup which retails for $5500 from PWR without the adapters.

Photos via email no problem.

Link to comment
https://www.sau.com.au/forums/topic/407280-alcon-brake-package-to-suit-nissan/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Murray_Calavera
      WTAC 2025

      By Murray_Calavera · Posted

      Yeah mate, never miss it.
×
×
  • Create New...