Jump to content
SAU Community

Recommended Posts

Red top SR20DET Long motor 100,000kms, with Loom $1200 (excluding turbo, injectors)

Have a vid of engine running and have had a compression test done

S13 Redtop ecu with Nistune $350

Garret GT3071R Turbo, .86 rear housing, 52 trim, Mint cond no shaft play $950

SARD 550cc injectors $400

SARD adjustable fuel pressure regulator, with earls fittings and adaptor $160

GENUINE Z32 Air Flow Meter $150 (no plug)

Walbro 255L/H Fuel pump $100

Can do all of the above as a full package ready to drop in for $3000, good for 240 – 250rwkw

3inch one piece dump and front pipe with O2 sensor $120

3inch stainless Fuitsubo exhaust with hi flow muffler and gutted cat $250

Turbosmart 38mm sleeper series dual port blow off valve $250

Greddy Profec B spec II Boost controller $300 ( pretty much brand new )

NEW Pod filter $50

Greddy catch can $50

DRIVELINE

Tomei 2 way diff in housing Housing ( 5 bolt ), 4.11 ratio $750

S13 gearbox 100,000kms $600

S13 manual tail shaft with centre bearing $100

S13 clutch master cylinder with slave and lines

S13 manual pedal box

Can do a deal for a full manual conversion minus clutch and flywheel

C's short shifter - $150

EXTERIOR

ORIGIN Roof spoiler $180

Crystal JDM tail lights $150

complete S13 Silvia doors – paint and trim in mint condition $120 each or both for $200

S13 boot lid, spoiler holes welded and has been re-painted mint $100

S13 rear stock bar with reo Mint $100

Windscreen good condition - $100

Rear window $100

16x8 genuine R32 GT-R alloys - $500

INTERIOR

S15 Rear seat complete $100

S13 Rear seats $20

Greddy GREX Gear knob $50

Black suede dished steering wheel $100

Bride Fixed back bucket, with drivers side rail (side mount)$400

Black Dash Mat $60

S13 dash mint condition no cracks or fading $200

S13 digital climate control with loom $100

SUSPENSION

Unkown rear strut brace $50

Tein HE coilovers front and rear with camber tops $750

Silk Road adjustable castor rods with rose jointed ends $100

5stud conversion with brakes

5 stud front hubs and bearings pressed onto S13 knuckles and uprights

R33 rear twin piston callipers(bendix Pads) with 5 stud hubs and drum brake set up

R32 BM44 brake master cylinder

R33 handbrake cable with adaptor plate

S15 front callipers with Bendix Ultimate pads, and RDA rotors

Total brake set up package: $700

S13 shell with damage! Has Walk in S,A Rego! (rego is for SR20DET) $800

all parts located in Adelaide, will post most items at extra cost

will have pictures up soon, can email/txt pics for now though

cheers

Walbro 255L/H Fuel pump $100

ORIGIN Roof spoiler $180

Crystal JDM tail lights $150

complete S13 Silvia doors – paint and trim in mint condition $120 each or both for $200

S13 boot lid, spoiler holes welded and has been re-painted mint $100

Can I get pics of these?

Cheers

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...